Q= 50 MPa, Tx= 30 MPa, %3D Oy= 80 MPa,

Q: If L, = 22 ±0.01 mm and L. =L, = %3D 10 +0.005 mm, then L (in mm) is %D %3D L3 L4

A:

Q: Three cables are connected at A, where the forces P and Q are applied as shown. Knowing that Q = 10…

A:

Q: 4. The control linkage of an airplane consists of a rigid member DBC and a flexible cable AB. A…

A:

Q: An air-standard Otto cycle is often used as a very simplified model of a spark- ignition engine. The…

A: P-V diag

Q: vapor pressure of acetone is 200 mm Hg at 22.7°C. Liquid acetone is kept in a sealed flask at…

A:

Q: What is the shape factor F12 for the situation shown in Fig. 1 below ? O 1.1 2m 2 m 0.001 O 0.33 3 m…

A:

Q: A rectangular bar of length L has a slot in the central half of its length. The bar has width b,…

A: Write the given data.Determine:- The overall the elongation of the bar

Q: You have 4 springs, each being 3.5, 6, 8.5, 11 N/m What's the smallest stiffness you can make using…

A:

Q: Water is the working fluid in an ideal Rankine cycle. The condenser pressure is 8 kPa, and saturated…

A:

Q: Nylon strips are fused to glass plates. When moderately heated the nylon will become soft while the…

A: Answer: The average shear strain in nylon due to load P is 0.1974 rad ( 11.3099°).

Q: rts are roller, and fixed Supports. Fig. 1. 21 (6) tang = tai

A:

Q: A wire in the wire drawing machine, at the entrance entrance It will be drawn from a drawer with 15…

A:

Q: Q2/What is the difference between the conceptual stage and embodiment stage? which one needs more…

A: Introduction: The conceptual design step formalizes the basic notion. It absorbs just enough…

Q: b-

A: GIVEN DATA A METAL PLATE IS GIVEN WE HAVE TO FIND ITS CENTRE COORDINATE X AND Y

Q: Why do most materials exhibit an increase in dimensions when heated?

A: Thermal Expansion of material : When the material heated it gets expands is called as thermal…

Q: dxes a parabolic spandrel. Assume uniform density pa-

A:

Q: The figure below shows a liquid-level system in which two tanks have cross-sectional areas, A₁ and…

A: To Find:A. The differential equation model for the system behavior in terms of the liquid heights…

Q: Consider 1.0 kg of a 99.4 wt% Fe-0.6 wt% C alloy that is cooled to a temperature just below the…

A:

Q: Two bars are used to support a load. When unloaded, AB is 5 in. long, AC is 8 in. long, and the ring…

A:

Q: Steam is entering the steam machine. It is a piston-cylinder assembly that moves vertically up and…

A: The pressure at point 1 is The volume at point 1 is The pressure at point 3 is The volume at point 3…

Q: Explain the Navfac (1982) Correlation for Sub grade Reaction Modulus ?

A: Modulus of subgrade reaction is outlined because the pressure per unit deformation of the subgrade…

Q: please make an ilustration relating pressure to area and force, it can be an example drawing

A: To make: An illustration relating pressure to area and force. Explanation: Consider an image below:…

Q: how do i find, Vba; Vbc; Vbd?

A:

Q: If a strengths-of-materials analysis determines the maximum torque that can be applied to a shaft is…

A:

Q: Determine the internal normal force, shear force, and bending moment at point C in the beam. 5 kN/m…

A:

Q: Explain about the term kernel and determine the size of kernel for a rectangular 200 mm x 300 mm.

A:

Q: The airplane on the left has a re the wind of 150 km/h. The spee relative to the ground is 15 km/…

A: The velocity diagram is as follows-

Q: Materials Tree Metals Ceramics Polymers Composites Ferrous Alloys Engineering Ceramics Thermosets…

A: Materials are mainly classified into four types, namely: Metals, Ceramics, Polymers and  Composites.…

Q: 2.5team is held in two compartments separated by a membrane. The total volume is 777 ft3, and the…

A:

Q: 1. Incompressible flow around a circular cylinder of radius a is represented by the steam function…

A: write the given expression    Ψ =-ur sinθ +ua2sinθrIn  polar coordinates , ur =1r ∂Ψ∂θ, vθ=-∂Ψ∂θ…

Q: A sailboat weighing 980 lb with its occupants is running down wind at 10 mi/h when its spinnaker is…

A: The weight of the boat is W = 980 lbThe initial speed is v1 = 10 mi/hrThe final speed is v2 = 16…

Q: Q3: What is the magnitude of true strain (e) if the true stress (o) is 15% larger than engineering…

A: Given data:- True stress=1.15×Engineering stress To find:- Magnitude of true strain

Q: Water flows at a rate of 2.4 ft³/s in an old, rusty 7.8-in.-diameter pipe that has a relative…

A: Given data:

Q: Ise the graphical method to construct the shear-force diagram and identify the magnitude of the…

A:

Q: From the given figure, determine the following characteristics of the resultant: (a) magnitude of R,…

A:

Q: Determine the tensions in cables AB, AC, and AD. 1.40 m 2.25 m 1.20 m 0.60 m B D 2.0 m AO 145 kg

A:

Q: 2-16 Consider a large 3-cm-thick stainless steel plate in which heat is generated uniformly at a…

A:

Q: The steel member shown below has a diameter of 69 mm, modulus of elasticity of E=200 GPa, and is…

A: Draw FBD

Q: What happens if you add a small imperfection to a system that has a saddle-node bifurcation?

A: A bifurcation is a shift in the qualitative nature of a solution as a control parameter is changed.…

Q: Give me the process of making a meat tenderizer using a shaper machine process. The picture below is…

A: As we know that it is a tool controlled by hand which makes mellow pieces of meat for cooking.

Q: Describe the concepts behind principal components and dimensionality reduction.

A: given; Describe the concepts behind principal components and dimensionality reduction.

Q: Why do the supports that resist a force, such as a pin, restrict displacement?

A: Supports are provided to make the best use of objects depends on the necessity.

Q: (Problem 4.18 from the text book) For the casting shown, determine the largest couple M that can be…

A:

Q: 8. The barometer shown in the figure contains mercury (p=13.59 g/cm³). If the local atmospheric…

A: