Q 4. The following data refers to a 12 cylinder, single acting two stroke marine diesel engine. Speed = 150 rpm, cylinder diameter = 0.8m, stroke of piston = 1.2m, Area of indicator diagram = 5.5 x 10^-4 sq. m, Length of the indicator diagram 0.06m and Spring value = 147 MPa /m. %3D

Q 4. The following data refers to a 12 cylinder, single acting two stroke marine diesel engine. Speed = 150 rpm, cylinder diameter = 0.8m, stroke of piston = 1.2m, Area of indicator diagram = 5.5 x 10^-4 sq. m, Length of the indicator diagram 0.06m and Spring value = 147 MPa /m. %3D

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please write the complete step-by-step solution in a clear manner. Thank you!
An engine cylinder has a compression ratio (r) of 7.5, a clearance volume of 35 cm3 and a piston stroke length of 325 mm. What is the bore diameter in millimetres (mm) for the engine cylinder to the nearest mm.
Question Design a 4 cylinder inline, turbo diesel engine to produce 103 kW of brake power at design speed when installed in a Multi-Purpose Vehicle (MPV). The square engine operates on a four stroke cycle and produces 20 bar of maximum brake mean effective pressure (bmep). Average piston speed is 11.5 m/s and bmep at peak power is 14.4 bar. If the decided values of torque position and torque increase are 50% and 28% respectively, determine the: a) bore b) stroke c) displacement d) maximum torque e) engine speed at peak torque as well as f) engine speed at peak power
For a sprak ignition engine the following readings were observed. cylinder diameter 10 cm, stroke length 10 cm and clearance gap between TDC and cylinder head is 10 mm. for such engine the compression ratio will be а. 11 O b. 10 c. 100 d. 110
A marine engine cylinder has a compression ratio (r) of 9.5, a clearance volume of 650 cm3and a piston stroke length of 675 mm. What is the bore diameter in millimetres (mm) for the engine cylinder. Give your answer to the nearest millimetre mm.
18 The power output of a six cylinder four-stroke engine is absorbed by a water brake for which the law is WN/20000 where the brake load, W is in Newton and the speed, N is in rpm. The air consumption is measured by an air box with sharp edged orifice system. The following readings are obtained. Orifice diameter 30 mm Bore 100 mm Stroke 120 mm Brake load 560 N %3D C/H ratio by mass Coefficient of discharge Ambient pressure Pressure drop across orifice Time taken for 100 cc of fuel consumption Ambient temperature Fuel density 83/17 0.6 %3D 1 bar 14.5 cm of Hg 20 s 27 °C 831 kg/m³ Calculate (i) the brake power (ii) the torque (iii) the brake specific fuel consumption (iv) the percentage of excess air and (v) the volumetric efficiency
A four-stroke SI engine 0.08 m bore (d), 0.10 m stroke (L), is tested at full throttle at constant speed. The fuel supply is fixed at 0.0011333 kg/s and the spark plugs of the four cylinders are successively short circuited without change of speed, brake torque being correspondingly adjusted. The brake power (bp) measurements are the following:With all cylinders firing = 12.5 kWWith cylinder No. 1 cut off = 9 kWWith cylinder No. 2 cut off = 9.15 kWWith cylinder No. 3 cut off = 9.2 kWWith cylinder No. 2 cut off = 9.1 kWThe lower calorific (or heating value, LCVf) of the fuel is 44100 kJ/kg. The clearancevolume (Vcl) of one cylinder 70.0 x 103 mm3. Determine:(a) Indicated power (ip) of the engine under these conditions.(b) The indicated thermal efficiency (c) The relative efficiency of this engine. (d) Draw schametic diagram
As a mechanical engineer, you were asked by your supervisor to monitor the operation of 4-stroke engine; as a result you got the following readings: > Imep = 780 kN/ m2 > Engine speed = 800 rpm > Brake Power 30 kW %3D %3D > nm = 85 % > B/S 0.7 You noticed also, that the inlet valve opens 10° before TDC and closes40° after BDC and it takes 0.0035 second after ignition for the charge to gain maximum pressure. Depending on the above readings, find the following engine parameters: a. The crank angle when the spark occursfor the maximum pressure to be at TDC b. The time period in second of inlet valve opening during one cycle c. The diameter of the engine d. The average piston speed 1 Upload file
1- A four-cylinder, two stroke cycle diesel engine with (10.9 cm) bore and (12.6 cm) stroke produces (88 kW) of brake power at (2000 RPM). Compression ratio is (18:1). Determine: (a) Engine displacement. Ans.: (4700.6 cm³). (b) Brake mean effective pressure. Ans.: (561.7 kPa).
I need answers to parts 13, 14, and 15, pertaining to the print provided.
None
A four-stroke SI engine 0.08 m bore (d), 0.10 m stroke (L), is tested at full throttle at constant speed. The fuel supply (m; ) is fixed at 0.0011333 kg/s and the spark plugs of the four cylinders are successively short circuited without change of speed, brake torque (4) being correspondingly adjusted. The brake power (bp) measurements are the following: With all cylinders firing With cylinder No. 1 cut off With cylinder No. 2 cut off With cylinder No. 3 cut off With cylinder No. 2 cut off = 9.1 kW 12.5 kW 9 kW 9.15 kW 9.2 kW The lower calorific (or heating value, LCV) of the fuel is 44100 kJ/kg. The clearance volume (Va) of one cylinder 70.0x10³ mm³. Determine: (a) Indicated power (ip) of the engine under these conditions. (b) The indicated thermal efficiency (Nind, th). (c) The relative efficiency (7el) of this engine.