3.mUST DRAW FBD Q-3: If the maximum force that any member can support is 4.2 kN in compression and 5 kN intension, determine the maximum horizontal force P that can be applied at joint B, for d = 1.2 m.BEd/2d/2+Q-3

Answered: Image /qna-images/answer/72f5b409-fdea-4e7a-947a-926957f76bd4.jpg

Answered: Q-3: If the maximum force that any…

Trigonometry (MindTap Course List)

10th Edition

ISBN:9781337278461

Author:Ron Larson

Publisher:Ron Larson

Chapter3: Additional Topics In Trigonometry

Section3.4: Vectors And Dot Products

Problem 7ECP

See similar textbooks

Similar questions

For the sphers x-12+y+22+z-42=36 and x2+y2+z2=64, find the ratio of their a surface areas. b volumes.
A force of P₂ = 850 N is exerted on control arm BC, which is securely attached to the solid 25 mm diameter shaft. Dimensions of the assembly are a = 200 mm and b = 130 mm. Determine the absolute maximum shear stress in the shaft at (a) point Hand (b) point K. Answer: A (a) (Tabs max) H = (b) (Tabs max)K = P₂ i K i b a B X ! MPa MPa
Consider a ﬂat metal plate to be placed vertically underwater with its top 2m below the surface of the water. Determine a shape for the plate so that if the plate is divided into any number of horizontal strips of equal height, the hydrostatic force on each strip is the same.
The Deligne Dam on the Cayley River is built so that the wall facing the water is shaped like the region above the curve y 0.3x² and below the line y 180. (Here, distances are measured in meters.) The water level is 36 meters below the top of the dam. Find the force (in Newtons) exerted on the dam by water pressure. (Water has a density of 1000kg/m³, and the acceleration of gravity is 9.8m/sec².) Answer:
A hand truck is used to move two kegs, each of a mass 32 kg. Assume g=9.8 m.s²² and neglect the weight of the hand truck. a=35 deg. 80 mm 350 mm 500 mm •G2 B 300 mm A P Determine in N the vertical force P that should be applied to the handle to maintain equilibrium when a=35 deg.
Write Newton’s Second Law of Motion for three-dimensionalmotion with only the gravitational force (acting in the z-direction).
The Deligne Dam on the Cayley River is built so that the wall facing the water is shaped like the region 0.6x² and below the line 2 above the curve y y = 280. (Here, distances are measured in meters.) The water level is 34 meters below the top of the dam. Find the force (in Newtons) exerted on the dam by kg m³ = water pressure. (Water has a density of 1000- and the acceleration of gravity is 9.8 m sec² .) " Note: Weight density of water is 1000 (9.8)=9800 N/m^3
Suppose that the dam currently has water at a level 10 meters below to top of the dam. Furthermore, let the water be at a depth of 150m that's the foundation (see the figure in 2b). Use work as demonstrated in class to find the force on the face of the dam, your axis must be somewhere on this means that the water does not reach the base of the damn, 9.8 m/s2. Show all necessary = 1000 kg/m³ and the base of the dam. 380 m 220 m 160 m 220 m (a) Hoover Damn Schematic and Dimensions (b) Usable Region of Dam
Determine the magnitude P of the vertical force required to lift the wheelbarrow free of the ground at point B. The combined weight of the wheelbarrow and its load is 273 lb with center of gravity at G. 23" Answer: P 16" B 20" 8" lb 21"
A wrench 1m long lies along the positive y-axis and grips a bolt at the origin (i.e. the wrench can be represented by vector <0,1,0>). A force is applied in the direction of the unit vector <0, 1/sqrt(2), 1/sqrt(2)> at the end of the wrench. Find the magnitude of the force in Newtons (N) needed to supply 5sqrt(2) N*m of torque to the bolt. torque = | r x F | if r = <0,1,0> and F = <0, 1/sqrt(2), 1/sqrt(2)> so the torque is equal to the magnitude of the cross product of these two vectors but I don't understand how to get incorporate the 5sqrt(2) N*m I know that the magnitude of the cross product must be equal to 5sqrt(2) but I am not sure how to work backwards to that answer, please help!.
A water trough 12 m long has ends shaped like inverted isosceles triangles, with base 6 m and height 4 m. Find the force on one end of the trough if the trough is full of water. Use pg = 9800 N/m³. O 56,800 N O 356,800 N O 256,800 N O 156, 800 N
A cylindrical tank, shown to the right, has height 8 m and radius 4 m. Suppose the water tank is half-full of water. Determine the work required to empty the tank by pumping the water to a level 6 m above the top of the tank. Use 1000 kg/m for the density of water and 9.8 m/s² for the acceleration due to gravity. 3 4 m Draw a y-axis in the vertical direction (parallel to gravity) and choose the center of the bottom of the tank as the origin. For 0 ≤ y ≤8, find the cross-sectional area A(y). A(y) = (Type an exact answer, using as needed.) 8 m

SEE MORE QUESTIONS

Recommended textbooks for you

Trigonometry (MindTap Course List)

Trigonometry

ISBN:

9781337278461

Author:

Ron Larson

Publisher:

Cengage Learning

Mathematics For Machine Technology

Advanced Math

ISBN:

9781337798310

Author:

Peterson, John.

Publisher:

Cengage Learning,

Elementary Geometry For College Students, 7e

Geometry

ISBN:

9781337614085

Author:

Alexander, Daniel C.; Koeberlein, Geralyn M.

Publisher:

Cengage,

Trigonometry (MindTap Course List)

Trigonometry

ISBN:

9781337278461

Author:

Ron Larson

Publisher:

Cengage Learning

Mathematics For Machine Technology

Advanced Math

ISBN:

9781337798310

Author:

Peterson, John.

Publisher:

Cengage Learning,

Elementary Geometry For College Students, 7e

Geometry

ISBN:

9781337614085

Author:

Alexander, Daniel C.; Koeberlein, Geralyn M.

Publisher:

Cengage,

Linear Algebra: A Modern Introduction

Algebra

ISBN:

9781285463247

Author:

David Poole

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

Q-3: If the maximum force that any member can support is 4.2 kN in compression and 5 kN in tension, determine the maximum horizontal force P that can be applied at joint B, for d = 1.2 m. B E d/2d/2+ Q-3