Q-1 A power screw is 25 mm in diameter and has a thread pitch of 5 mm. (a) Determine the thread depth, the thread width, the mean and root diameters, and the lead, provided square threads are used. (b) Repeat part (a) for Acme threads.

Q: This still doesnt answer how to get points 2,  2', and 1', so how did you get it?

A: Itis asked to explain how the state points 2, 2' and 1' are obtained

Q: 355 coupe for some maintenance check. Before proceeding to your regular maintenance routine, it is…

A: Odd matric number:

Q: 18. How far off from the center of the support is the center of the two holes in the bosses of the…

A: 18)    Distance=4.2-0.66                   =3.54 in

Q: Convert the decimal number 35710 into its octal number equivalen

A: Steps Write the given decimal number. If the given decimal number is less than 8 the octal number…

Q: how o create all parts list after the drawing ?

A: Given question: how to create all parts list after the drawing ?

Q: Part C - Radius of curvature for AB and BC Determine the radius of curvature for AB, PAB, and for…

A:

Q: In Part a, could you please explain where the 4 comes from on the line before the answer.

A:

Q: Says.003 is wrong

A:

Q: If 17 welders can complete a job in 134 hours, how long will it take for 21 welders to do the same…

A:

Q: In the scale of inches, draw material edge at 7.00 diameters with six holes at 50 diameters. The six…

A:

Q: What is the SAE horsepower of an 8-cylinder engine with a bore of 4.556 inches? Round to the nearest…

A: Given data:- no of cylinder (n)=8 bore (d) =4.556 inches To find:-the SAE horsepower

Q: Draw Front and Side and top with all dimensions please

A: Find Draw the front, side, and top of the object with dimensions.

Q: With reference to the drawing callout in figure 5 below, which part(s) would 'pass' or 'fail' along…

A: Data given-  Dimensions of standard size  0.25±0.01 So tolerance is equal to 0.02  And the upper…

Q: The cord of a bow string drill was used for

A: The bow drill was used in ancient period.

Q: Another name for "SIZE DESCRIPTION is: 37 A Dimensioning B Orthographic projection. C Assembly…

A: Given Engineering drawing To find Size description Leader line Extension line

Q: 1.00 1.38 3.38 38 2.00

A: Select the correct statement about the notation circled in green and marked as letter D. Assume all…

Q: what is the scale if a line is 10 inches but is  drawn 5 inches long.

A: Finding scale if a line is 10 inches but is  drawn 5 inches long.

Q: is 60 left or right?

A: The horizontal reaction at A: 60 kN (Right)......(Option D)

Q: This is no answer sorry the answers are offered A B C or D

A:

Q: solve parts 4 and 5 please

A: To draw Mohr circle and to show the orientation of the element of maximum in plane shear stress

Q: Question attached

A: (a) Relative humidity is the ratio of the partial pressure of water vapour in the mixture to the…

Q: PART VI. Given that f(x,y) = (x +y)/2k, where x=-1,1,2 and y= 0,2,4 1. Find k 2. Find the marginal…

A:

Q: Can you show the work but written out please so I can see the steps better.

A:

Q: Can I get a more detailled explenation on how to get the numbers in the numetor in each fraction…

A:

Q: now please answer question 2 and 3 please

A: This question is based on the concept material science. As per the guidelines we are subjected to…

Q: The number of teeth on a gear is 27 and the outside diameter is measured as 10 mm. The module of the…

A: Given Data No. of teeth is 27 Outside diamtere is 10mm

Q: How do you solve parts a,b and c?

A:

Q: I need answers for 7,8, and 9,

A: A 0.250”X0.250” square hole.

Q: . Convert the octal number 23228 to its decimal number equivalent, (base-8 to base-10).

A: Givenoctal number =23228

Q: C) What is the maximum possible mass flow rate that the pump can produce?

A:

Q: Answer in 4-10

A: Given: →h1=3387.31 KJ/Kg→h2'=3074.5 KJ/Kg→h3=3457.04 KJ/Kg→h4'=3109.82 KJ/Kg→h5'=2384.82…

Q: Consider the crank assembly of the figure. The bearings at points A and B are in good alignm…

A:

Q: The Answer is cut off on the right side.

A: