pure aluminum is being poured into a sand mold. The metal level in the pouring basin is 10 in. above the metal level in the mold, and the runner is circular. What runner diameter is needed to ensure a Reynolds number of 2000? how long will a 20 in' casting take to fill with such a runner? given that Pure aluminum has a density of 2700 kg/m' and a viscosity of around 0.0015 N.s/m2 at 700 °C. Usev 87.9 in/s 2.23 m/s for the Reynold %3D number. (

pure aluminum is being poured into a sand mold. The metal level in the pouring basin is 10 in. above the metal level in the mold, and the runner is circular. What runner diameter is needed to ensure a Reynolds number of 2000? how long will a 20 in' casting take to fill with such a runner? given that Pure aluminum has a density of 2700 kg/m' and a viscosity of around 0.0015 N.s/m2 at 700 °C. Usev 87.9 in/s 2.23 m/s for the Reynold %3D number. (

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1a. What is “surface tension”? 1b. What is “capillarity”? 1c. What diameter of clean glass tubing is required so that the rise of water at 20oC in atube due to capillary action is less than h = 1.0 mm?
What is press vessels?Application of plane stresses in pressure vessels. Please explain briefly
Draw the fallowing in cubic system :- (020) ,(222) , (101) , (201) , (111)
Im needed the solve max 30-45 minutes and please send Im very needed. Thank u Manufacture and design a U-pipe in an open state with a minimum of 7 different fluids with a datum. NOTE Examples of answers such as the available images and there are also problems from the 2 available images. The answer does not need to use numbers as in the example answer
A piping system is made of 6-nominal schedule 40 cast iron. All fittings are threaded fittings (Class 125). Discuss whether or not this piping system is suitable for handling liquid water at room temperature and fluid pressure of 450 psi. | If yes, provide supporting information. | If no, suggest the changes that could be made to the piping system.
Make comments on relationship viscosity-shear rate for shear thinning shear thickening and Newtonian fluids.
Which are not true about Capillarity? (a) Capillary rise increases as the surface tension increases (b) A small bore tube will produce a higher capillary rise (c) Temperature will not affect the capillary rise of a liquid (d) In wetting fluids inside a tube, adhesion is less than cohesion, (e) If the wetting angle is greater than 90 degrees, the fluid inside a tube will fall (f) Dense fluids will rise less inside a thin bore tube, (g) The specific gravity of a fluid does not affect the capillary rise
A certain liquid at 20 deg.C has a viscosity of 0.000651 Pa.s. What shear stress is required to deform this fluid at the shear rate of 4900 per second?
Question 3 The component shown in Figure 3 is casted from grey cast iron, with a density of 7150 kg/m and a viscosity of 0.014 Ns/m², at the casting temperature of the material. The casted component has a volume of 0.0022 m3 and is manufactured through the sand casting process. During the casting process the metal level in the pouring basin is 300 mm above the metal level in the mould. The runner have a circular profile of Ø 12 mm. Ø 300,0 Ø 200,0 Ø100,0. 1.6/ R5 R5 60 H7 SECTION A-A Figure 3: Component to be casted 3.1 Calculate the velocity and the flow rate of the metal into the mould. Is the flow turbulent or laminar? 3.2 If product shown in Figure 3 is to be casted in aluminium, which factors should be considered if the same pattern and mould configuration (shown in Figure 4 below used to cast the product from cast iron), is used to cast the product from aluminium? Cope Sprue Parting line Gate Drag Runner Figure 4: Mould configuration used to cast the component in grey cast iron…
Question 3: A tape, of width w= 25.40 mm is to be coated on both sides with a lubricant by drawing in through narrow gap of length, L as depicted in Figure 2. Following below values are given: c = 0.300 mm, t = 0.381 mm, and L = 20.0 mm. The lubricant, of dynamic viscosity u = 1.0054 kg/m.s completelys fills the gap and the velocity distribution is asssumed to linear as shown in Figure 2. The maximum allowable force in tape is given as F = 30.04 N. Find the maximum allowable tape speed Figure 2
A 6.0-m diameter cylindrical tank contains a hazardous material dissolved in mostly water. A leak occurred in the tank because a 0.1 m diameter pipe located 1.0 m above the bottom of the tank was accidentally disconnected. A 30-minute emergency response time is required to stop the leak. If the tank is vented to the atmosphere, calculate the following a) If total emptying time is 2.5 hours what is the original liquid level in the tank just prior to the spill. b) What is the liquid level in the tank at the end of the spill? (e c) Estimate the total amount of liquid spilled from the tank in m³ (V) and in kg (m). 2) (Assuming Co=0.61 for the highly turbulent flow; Assuming p = pwater =1000 kg/m³) | P₁ = 0 น hL 1 m P = Ambient Pressure
Calculate the liquid viscosity of water at 299.35 K in Pa-s. Use the DIPPR tables.