proplems1.A single solar cell (10 cm x 10 cm) produces a voltage of 0.5 V and a current up to 2.5A. If the solar insolation is 800 W/m2, the efficiency of the solar cell is?2.Calculate the amount of power obtained from a solar site containing 500 solar panels,each It consists of 100 solar cells and calculate the conversion efficiency of the product ifyou know the amount of solar energy Falling onto a single plate equals 1000 watts.3. Find the number of cells required to generate power equipped for a product equal to 50kW and area Required for the solar station if you know that one panel contains 50 solarcells and its area is 1 Square meters

As per our guidelines, we can answer one question. please resubmit remaining questions.

Answered: proplems 1.A single solar cell (10 cm x…

Similar questions

A motor is set up lifts a mass similar to the setup used in class for the efficiency of the motor lab. 6.8 V was applied to the motor and 2.2 Amps of current flowed through it. The motor was attached by a string to a mass, and as the motor turned, the 0.26 kg mass was lifted 3.1 meters in 1.7 seconds. How much electrical power was input to the motor, and how much mechanical power was produced? O 15 Watts of electrical power input,7.9 Watts of mechanical power output O 7.9 Watts of electrical power input, 6.8 Watts of mechanical power output O 15 Watts of electrical power input, 4.7 Watts of mechanical power output O 4.7 Watts of electrical power input, 6.8 Watts of mechanical power output O 4.7 Watts of electrical power input, 15 Watts of mechanical power output O 7.9 Watts of electrical power input, 15 Watts of mechanical power output 13 14 15 16 17 18 19 20 21 22 novo Ce Ol
1. Construct a truth table for the figure.2. Obtain the MINTERM expression from the truth table.3. Draw the circuit diagram for the MINTERM expression
Topic: Wed 12/8 Reading Quiz canceled... Review Homework 2. Classify the above reaction. Choose among one or more from com combustion. 6. Circuit Consider the following setup V R2 R1 1. Are R1 and R2 connected in series or parallel? 2. If R1 = 20kN and R2 = 40KN what is the equivalent resistance? 7 Falling Rock A rock is dropped off of a cliff. It takes 2.8s for the rock to reach the 9.81. How tall is the cliff? 8 Middle C and C# Middle C has a frequency of 261.63HZ. The note C# has a frequency of a particular piano us 40.0cm long. How long must the C# string be if it therefore the same wave velocity) as the C string? ww ww
5. Assume that you need to measure an average temperature in a heated space. You have three identical temperature sensors. Each sensor produces a voltage proportional to temperature such that: Sensor Voltage = .01 * Temperature in degrees Celsius Assume that you bave three voltages, Va, V, and V, You want to take the average of these three voltages lin order to compute the average temperature inside the heated space. This circuit has been suggested as a possibility for computing the average. Rf ww Vout A. Find an analytical expression for Vout in terms of the input voltages and the four resistors. B. Determine if a proper dhoice of resistors will let you use this as a averager. If you can, then find some appropriate values for the resistors.
1. Use the following diagram to answer the questions below. a. What are the single resistor elements in series? b. Calculate the equivalent resistance of the circuit The voltage of the source is 90V 12.27A 20 10 20 30 ww 10 20 10 1.64A
Please fast
b. In the space below construct a series and parallel circuit with 3 resistors (2, 4, 6), 12v battery (3 cells), and a closed switch. c. Calculate the equivalent resistance one can put to replace the 3 resistors in series and the 3 resistors in parallel. d. Insert an ammeter to measure the total current in both circuits. e. Insert voltmeter to measure the potential difference across the 2 ohm resistor in the series circuit. f. Determine the reading the ammeter will give in each circuit and reading the voltmeter will give in the series circuit.
question in photo please asap