Procedure 1. Using the DC circuit trainer, connect the circuit Shown in Fig. (4), take VT =10V, and R1=822, R2 = 1002 and R3 =150N. 2. Measure the voltage and current of "R , R2 & R;", then record it in table below 82Ω 1002 1502 V(volt) VT= I(mA) IT = 3. Byusing ohm's law, Calculate the RT. 4. Disconnect the DC power supply, and then measured the equivalent resistance by using the AVO meter only. 822 Соpper -connecting I wire 10V 1002

Procedure 1. Using the DC circuit trainer, connect the circuit Shown in Fig. (4), take VT =10V, and R1=822, R2 = 1002 and R3 =150N. 2. Measure the voltage and current of "R , R2 & R;", then record it in table below 82Ω 1002 1502 V(volt) VT= I(mA) IT = 3. Byusing ohm's law, Calculate the RT. 4. Disconnect the DC power supply, and then measured the equivalent resistance by using the AVO meter only. 822 Соpper -connecting I wire 10V 1002

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Preview File Edit View Go Tools Window Help 88% O Wed 9:06 PM A Laboratory 7 - Series-Parallel DC Circuits.pdf (page 4 of 7) -Edited Q Search Aal v Av V Laboratory 7 - Series-Parallel.. Assuming a 12 V dc supply is connected to the circuit as shown, calculate: I, l1, l2, l3, V1, V2 and V3. Record the values in the table. Be sure to indicate the correct unit for each quantity. V, R2 1kQ R1 12V V, 2.2ko 13 V3 3 R3 3.3kQ Parameter Calculated Measured RT 12 13 V1 V2 V3 4 Help étv
PROJECT CIRCUIT BREAD BOARD (TINKERCAD) - DC VARIABLE POWER SUPPLY LM7805 LM7805CT LINE VOLTAGE VREG COMMON R1 24700 C2 =0.27µF R3 23.3kQ C3 10pF D1 R2 V1 24 V 1kQ С1 누2200μF 50% | 12.627 1B4B42 ALED1 国 R2 (Pot) 1 4 7. Position VC3 VR2 VR3
DC NETWORK ( NEED NEAT HANDWRITTEN SOLUTION ONLY OTHERWISE DOWNVOTE).
Consider two odd solar cells. Cell No.1 has Is1 - 25 nA, ni = 1.5, Rs1 = 102, Cell No.2 has L₂ = 0.1 nA, n₂=1, R2=5 2.The illumination levels and efficiencies are such that ILI = 10 mA and I12-25 mA. Use equivalent circuits and Spice to analyze and plot the I-V characteristics and power output vs operating voltage characteristics of these cells, operated individually. Determine the maximum power each cell can deliver, the corresponding voltages and currents at their maximum power points. Repeat the above when these two cells are connected in series to deliver a higher voltage and compare the total maximum power they generated separately vs when connected in series. Write your comments.
1. (a) A DC circuit is shown in Figure 1 and it is working under steady state conditions. R3 22 L1 1m V1 V2 12V 24V R4 22 R1 R2 R5 R6 10 10 47 18 IT Figure 1 (i) Calculate the total current, IT, in the circuit shown in Figure 1. (ii) Calculate the power dissipated in resistors R1, R3, R5 and R6. (iii) How would the total current, IT, change if a capacitor was used instead of L1 under steady state conditions?
i need the answer quickly
gurumuda.net/physic IL 3. R₁ = 4 ohm, R₂ = 6 ohm, R3 = 2 ohm, and V = 24 volt. What is the electric current in circuit as shown in figure below. R₁ R₂ + 0 : K₁
In the circuit given below, V1=10cos (100t) volts and V2=2 volts. Find the expressions of the currents 11 and 12 in the time domain. +1 (+1 V1 V2 2V R1 5 ohm 1₂ +₁. R3 5 ohm L1 0.2 H R2 4 ohm I₁ C1 10 mF
In the circuit in the figure emf of the battery&= 20 V. R All the inductors are of the R, L, L same inductance, L=0.05 H and of negligible resistances. Resistances of the resistors %3D %3D %3D are Ro = 32, RỊ = 10, R2 = 42, R = 49, Rq = 40, Rg = 50. %3D %3D R = 30. The switch S is closed at the time t = 0. What is the current flowing in Ro long after the switch S is closed?
Please give proper explanation so that i can understand
%TV l. M E O O A:09 docs.g هدی عبدال له عبدال. . . B2/for the figure b rv+ shaded Area : * 3 cm y=kx? 8 cm 7 cm 6 cm 49.23 51.66 50.76 45.32 47.81 53.22 B2/(b) X-bar * 3 points II
2. (a) A capacitor C1 is connected in a DC circuit as shown in Figure 3. The supply voltage Vs=24Vdc, R1 = 1.5kN, C1 = 150µF and R2 = 8200. SW1 R1 R2 Vs C1 Figure 3 (i) The circuit in Figure 3 is initially de-energised. What happens after closing switch SW1? (ii) Write down the equations to show how the current through C1 and the voltage across C1 change after closing switch SW1. (iii) What is the value of the current through R2 while SW1 is closed? (iv) After 5T, Sw1 is opened. What is the current through SW1 while opening? (v) Describe how the circuit behaves when SW1 is opened? (vi) Write down the expressions to show how the current through C1, the voltage across C1 and the current through R2 change after opening SW1. (vii) Draw a graph to show how the current through C1, voltage across C1 and current through R2 change while operating SW1. (b) If an inductor was used instead of C1 in Figure 3, explain the importance of R2 and what could happen if R2 was not connected.