P r:07Asiacell I.O Engineering Mechanics Ch1 &Ch2.pdf piProblems:F2-4. Resolve the 30-lb force into components along theu and e axes, and determine the magnitude of each of thesecomponents.F2-1. Determine the magnitude of the resultant forceacting on the screw eye and its direction measured clockwisefrom the x axis30 Ib154530602kN5kNProb. F2-1Prob. F24F2-2. Two forces act on the hook. Determine the magnitudeof the resultant force.F2-5. The force F-450 Ib acts on the frame. Resolve thisforce into components acting along members AB and AC,and determine the magnitude of each component.304530450 Ib200 N40500 NProb. F2-2Prob. F2-5F2-3. Determine the magnitude of the resultant force andits direction measured counterclockwise from the positivex axisF2-6. If force Fis to have a component along the u axis ofF-6 kN, determine the magnitude of Fand the magnitudeof its component F, along the e axis800 N4510530600 NProb. F2-3Prob. F2-617Engineering Mechanics/Statics- R. C. Hibbeler ver.14Power Mechanics Techniques Engineering/Tariqg Al-Khalidi*2-4. The vertical force F acts downward at A on the two-2-1. If e = 60 and F = 450 N, determine the magnitudeof the resultant force and its direction, measuredcounterclockwise from the positive x axis.membered frame. Determine the magnitudes of the twocomponents of F directed along the axes of AB and AC.Set F = 500 N.2-2. If the magnitude of the resultant force is to be 500 N,directed along the positive y axis, determine the magnitudeof force Fand its direction 8.2-5. Solve Prob. 2-4 with F= 350 lb.15700 N

∈FX = 2 COS 45 - 6 COS 60∈FX = -1.585KN∈FY = - 2 SIN 45 - 6SIN 60∈FY =-6.61KNresultant =…

Problems: 2-1. Determine the magnitude of the resultant force acting on the screw eye and its direction measured clockwise from the x axis F2-4. Resolve the 30-lb force into components along the u and e axes, and determine the magnitude of cach of these components. 30 Ib 15 30 2kN Prob. F2-1 Prob. F24 F2-2. Two forces act on the hook. Determine the magnitude of the resultant force. F2-5. The force F- 450 lb acts on the frame. Resolve this force into components acting along members AB and AC, and determine the magnitude of cach component. 30 450 Ib 200 N 40 S00N Prob. F2-2 Prob. F2-5

Problems: 2-1. Determine the magnitude of the resultant force acting on the screw eye and its direction measured clockwise from the x axis F2-4. Resolve the 30-lb force into components along the u and e axes, and determine the magnitude of cach of these components. 30 Ib 15 30 2kN Prob. F2-1 Prob. F24 F2-2. Two forces act on the hook. Determine the magnitude of the resultant force. F2-5. The force F- 450 lb acts on the frame. Resolve this force into components acting along members AB and AC, and determine the magnitude of cach component. 30 450 Ib 200 N 40 S00N Prob. F2-2 Prob. F2-5

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

6:44 X Q2-P3-ANALYSIS OF STR... 2 of 2 PROBLEM 2 Û Determine the forces in members GB, GF, GC and BF by the: a). Method of Joints b). Method of Sections чки AKN # W in 3 KN. akn 3m 3m from from from t 3m 624 3 KN 3m
Hand written and clean writing please
Draw the FBD an determine the reactionsof the beam.
statics of rigid bodies
Determine the design key points A, B, C, D and E on the section capacity line (N-M, interaction diagram) for the column section shown in Figure below for the case where 4N24 bars in each face. Bending takes place about the x-axis, f'= 40 MPa, fy-500 MPa, and E,=200 GPa 4N24 4N24 a D O O O y 600 mm O 72 mm x - - 72 mm I 600 mm 71
2-2 A 100-N force is applied at end C of the rod as shown. c) Assess the effect of the angle being varied from 0° to 360° to the moment of the 100-N force about point A. [b) (i) MA=0 N-m; (ii) MA=-24k N-m; (iii) MA=-12k N.m] 2-3 A 600-N force is applied on end D of the bent rod as shown. c) Assess the effect of the angle being varied from 0° to 180° to the moment of the 600-N force about point A. [b) (i) MA= 180 N-m; (ii) MA= - 480k N-m; (iii) MA= 180k N-m; (iv) MA=- 432k N.m] Figure IA Figure 150 mm P2-2 600 N 50 cm B P2-3 90 mm 0 000 B 30 cm C 100 N 30 cm
Solve for the force members using Method of Joints
A force of P is applied perpendicular to the handle of the mechanism. If the magnitude of force F of the woodblock on the clamp is F=58 lb, what force P is applied? The members are pin connected at A, B, Cand D.
Member ACDF is a rigid bar. Links BC and DE are made of steel (E = 29,000 ksi) and are ½/2" wide and ¼" thick. If the applied force P is 1000 lb, what is the force in each of the links and the deflection of point A? B -4 in. D F 4 in. 2 in. 2 in -5 in.- 2210
determine determinancy and stability identify the zero force members.