Problem2: Knowing that the cross section of the bar is a square of side 40 mm and the strain & on A is 450μm, Determine the magnitude of P for the eccentric loading shown. Use E = 200GPa. 40 mm 40 mm A+ B A; 80 mm I B P

Problem2: Knowing that the cross section of the bar is a square of side 40 mm and the strain & on A is 450μm, Determine the magnitude of P for the eccentric loading shown. Use E = 200GPa. 40 mm 40 mm A+ B A; 80 mm I B P

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The sanding-drum mandrel shown in the figure is made for use with a hand drill. The mandrel is made from a rubber-like material that expands when the nut is tightened to secure the sanding sleeve placed over the outside surface. If the diameter D of the mandrel increases from 1.95 in. to 2.05 in. as the nut is tightened, determine (a) the average normal strain along a diameter of the mandrel. (b) the circumferential strain at the outside surface of the mandrel. Sanding sleeve Mandrel Answers: (a) ED = in./in. (b) Ec = in./in. Save for Later Attempts: 0 of 1 used Submit Answer
Suppose that a= 420 mm and b= 560 mm Part A: Determine the average normal strain along diagonal BD Part B: Determine the average shear strain at corner B relative to the x, y axis
Part of a control linkage for an airplane consists of a rigid member CB and a flexible cable AB Originally the cable is unstretched. Part A If a force is applied to the end B of the member and causes a normal strain in the cable of 0.00485 mm/mm, determine the displacement of point B Express your answer to three significant figures and include appropriate units. AB= μA Value CE ? Units B A 800 mm 600 mm
A thin rectangular plate is uniformly deformed, as shown. Determine the shear strain γxyγx⁢y at P. Assume a = 1200 mm, b = 580 mm, c = 1.3 mm, and d = 1 mm.
The rigid bar ABC pivots about support B. After application of load P, end C of the rigid bar moves upward by 0.06 in. If the length of bar (1) is L₁ = 51 in, determine the average normal strain in bar (1). Assume that a = 135 in., b=32 in., and c = 0.06 in. 4₁ 1 a Rigid bar B b
5. A material is subjected to principal stresses o, and o, . Determine the orientation 6 of a strain gauge placed at the point so that its reading of normal strain responds only to o, and not o, . The material constants are E and v. (assume E = 200GPA, v = 0.3 )
The sanding-drum mandrel shown in the figure is made for use with a hand drill. The mandrel is made from a rubber-like material that expands when the nut is tightened to secure the sanding sleeve placed over the outside surface. If the diameter D of the mandrel increases from 1.95 in. to 2.05 in. as the nut is tightened, determine (a) the average normal strain along a diameter of the mandrel. (b) the circumferential strain at the outside surface of the mandrel. Sanding sleeve D - Mandrel Answers: (a) ED = i in./in. (b) Ec= in./in.
When an axial load is applied to the ends of the bar shown, where L₁ = 30 in. and L₂ = 80 in., the total elongation of the bar between joints A and C is 0.100 in. In segment (1), the normal strain is measured as 1700 µin./in. Determine the normal strain in segment (2) of the bar. A (1) L₁ 662 μin./in. O 784 μin./in. O 373 μin./in. O 719 μin./in. O 613 μin./in. B (2) L2
The bar has a length of 8 in. and a square cross-sectional 5000 lb 5000 lb area of 0.5 in. x 0.5 in. It is made of a material having the stress-strain diagram shown. If the bar is subjected to an 8 in. σ (ksi) axial force of 5000 lb, determine 75 (a) the change in the 8-in. length, 60 (b) the change in the 0.5-in. thickness. 45 Assume Poisson's ratio is 0.30. 30 15 € (in./in.) 0.001 0.002 0.003 0.004 0.005 0.006 0.007
Your answer is partially correct. The strain components for a point in a body subjected to plane strain are ɛ, = -890 µɛ, ɛ, = -690µɛ and yy = -682 prad. Using Mohr's circle, determine the principal strains (ɛp1 > Ep2), the maximum inplane shear strain yip, and the absolute maximum shear strain ymax at the point. Show the angle 0, (counterclockwise is positive, clockwise is negative), the principal strain deformations, and the maximum in-plane shear strain distortion in a sketch. Answers: Ep1 = 927.99 με. Ep2 = 1116.0 PE. Vip = 188.01 prad. Ymax = -188.01 prad. Op = 36.82