Problem.. a) For the system below, plot the total potential energy for different values of displacement at the loaded / free end of the spring. Using these data, what is the approximate minimum potential energy of the system and what displacement results in the minimum potential energy? b) Using the Principle of Minimum Potential Energy, determine the "exact" displacement that results in the minimum potential energy for the system? Show that this displacement results in a stable equilibrium position.

Q: LESSON: AUTODESK AUTOCAD Choose from the choices:

A: The broken line is used to draw the large drawings which are not possible to draw on the sheet,…

Q: %o change in diamefesx-?

A: Given; Solid cylinder of; diameter,d1=120 mmheight,h1=50 mmTwo frictionless flat dies to a…

Q: re 2) mine the smallest allowable diameter of the roc able bending stress is allow = 225 MPa.

A: Apply the moment equilibrium condition about point A.The force equilibrium condition along the…

Q: If A=0.375 inch, B=0.923 inch, C=1.0992 inches, find G A 기사 W -|×|-> G- -B- -C- F E-

A: If A= 0.375 inch, B=0.923 inch, C=1.0992 inches,find G.

Q: a= 15.0 in, b= 7.0 in, c= 12.0 in, and d= 12.0 in.,(e = 3.0 in. horizontal), Draw the kinematic…

A: Given mechanism:                           Given datalength of link a = 15 inlength of link b = 7…

Q: I didn't understand how you fond the angle teta

A: For solution refer below images.

Q: With reference to the drawing callout in figure 5 below, which part(s) would 'pass' or 'fail' along…

A: Data given-  Dimensions of standard size  0.25±0.01 So tolerance is equal to 0.02  And the upper…

Q: 1.00 1.38 3.38 38 2.00

A: Select the correct statement about the notation circled in green and marked as letter D. Assume all…

Q: e b a What is the degree of freedom of the mechanism? а. 3 O b. 0 Ос. 1 d. 4 е. 2

A: Degree of freedom is given by the following relation, F=3(l-1)-2j-h Where l=no.of link=4 j=no.of…

Q: A 2.10kg pole is attached to a wall with a hinge as shown. A 5.80kg sign is suspended at the other…

A: Given data: mp=2.10 kgM=5.8 kgD1=1.3 mD2=3.2 mα=19.0° Need to determine the torque on the pole due…

Q: Write the following as full (decimal) numbers with standard SI units. b. 10cm c 1001 g d. 48cl

A:

Q: A. Poppet valveu The number of degrees the camshaft turns during one four-stroke cycle. B. Blowby…

A:

Q: name these lines

A: The names of the given lines is given below.

Q: Z is incorrect

A:

Q: Identify the drawings as isometric, trimetric, oblque or perspective. A. B

A: Isometric projection is a technique used in technical and engineering drawings to visually…

Q: What is the v-velocity at the centerline after refining the mesh

A: To explain: What is the v-velocity at the centerline after refining the mesh.

Q: If A=0.375 inch, B=0.923 inch, C=1.0992 inches, find G A 기사 W -|×|-> G- -B- -C- F E-

A:

Q: What is Line G?

A: Solution:

Q: Interpret the significance of the letters shown in the illustration

A: Instruction given at tail of the welding symbol is "See detail A".Here detail A will have the…

Chemical and Phase Equilibrium

Phase diagrams or equilibrium phase diagrams are the graphical representations that show the phase transformations of the constituting elements with respect to the pressure, temperature, and compositions. The diagrams show the conditions that limit the different phases, namely solid, liquid, and gas. The diagram can also be utilized to verify the relations between the state variables. Most of the phase diagrams are temperature-pressure phase diagrams, with the variable parameter as the composition. Usually other variables such as solubility and pressure parameters are not indicated in the phase diagram. For a one-component system (unary phase diagram), the phase diagram is generally a function of temperature and pressure as the state variables, or temperature and volume. However, for a binary system (two-phase) having two components, the phase diagram is a function of temperature and composition as the state variables only. Coexisting of the different phases of the constituting elements is indicated in the phase diagram. A ternary phase diagram can be characterized by consisting of three phases in equilibrium.