[wikproblem-Two: A Cylindrical stainless steel inget (keys)15 cm in diameter and 40 cm long passes through a treatmentference that is (6m) in length. The temperature of the furance guis (1300°C). The inital ingot temperature is (100°C). TheCombined het radinat and Convective heat transfercelli--cient is (100 tk). Calculate the maximum speed withwhich the ingot should pass through the furnace if itmust attain a temperature of (850 °C). Take (α=0.46×105(Aust Velocitga 1.985 mm/3)-5

D=15cm=0.15mL=40cm=0.4mT0 = 1000 °C (intial Temperature)Tf = 8500 °C (final Temperature)

problem-Two: A Cylindrical stainless steel inget kryst 15 cm in diameter and to cm long passes through a treatment ference that is (6m) in length. The temperature of the furance gu (1300°C). The initial ingot temperature is (100°C). The is cient is Combined het radiant and Convective heat transfer caffi- (100). Calculate the maximum speed with which the ingot should pass through the furnace if it must attain a temperature of (850 °C). Take (α=0.46×105 (Ansi Velocity 1.985 mm/3)

problem-Two: A Cylindrical stainless steel inget kryst 15 cm in diameter and to cm long passes through a treatment ference that is (6m) in length. The temperature of the furance gu (1300°C). The initial ingot temperature is (100°C). The is cient is Combined het radiant and Convective heat transfer caffi- (100). Calculate the maximum speed with which the ingot should pass through the furnace if it must attain a temperature of (850 °C). Take (α=0.46×105 (Ansi Velocity 1.985 mm/3)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Calculate the heat transfer coefficient for forced convection local boiling of water in a vertical pipe at 8 atmospheres pressure, 12°C surface superheat.
I need answer within 20 minutes please please with my best wishes
SOLVE STEP BY STEP IN DIGITAL FORMAT The SOLFIES company is dedicated to welding any type of metal, but especially aluminum parts. If the aluminum pieces that are welded come out at 1200°C and to speed up the cooling they are immersed in a tank full of water with a temperature of 0°C. In this case, the heat is transferred from the welded part to the water, causing the temperature to begin to decrease. Taking into account the temperature data of both the piece and the water, in addition to the value of the constant K= 0.02, it is necessary to know how long it takes for the piece to reach a temperature of 20°C in order to handle it and deliver it to the customer. MATH MODEL T'+KT=Tm Solve this differential equation with Euler's numerical method.
Two inches of urethane foam will reduce heat loss close to 1000% when applied to a 2-inch diameter uninsulated steel pipe. Assume the pipe wall thickness is 0.25-inches, the pipe interior convective heat loss (hi) is 500 BTU/hr-ft2-oF, and the pipe outside convective heat loss ho 20 BTU/hr-ft2-oF, k steel is 25 BTU/hr-ft-oF, and k insulaton is 0.023 BTU/hr-ft-oF. (hint - calculate heat loss with and without insulation.
Answer correctly and quickly as possible please. Please help me with my last three questions, I do not have any ask an expert left. Please.
WORK PROBLEM 7-29 IF GLAZING SYSTEM IS 56. 7:27. FOR 3:00p.m. SOLAR TIME, ON JULY 21, IN BOISE, ID. A 3ft WIDE AND 5ft HIGH WINDOW FACES SOUTH WEST- (ACTUALLY, IT FACES SOUTHWEST ALL THE TIME!) THE NEW INOPERABLE WINDOW HAS A 2in. WIDE ALUMINUM FRAME WITH A THERMAL BREAK UTILIZING METAL SPACERS. THE GLAZING SYSTEM IS 21C IN TABLE 7-3. THERE IS NO INTERIOR OR EXTERIOR SHADING. CALCULATE THE TOTAL SOLAR HEAT GAIN, USING THE SIMPLIFIED APPROACH.
a buildiug has the following calculated cooling loads: RSH gain 300 kW RLH gain = 110 kW The space is maintained at the following conditions Room DBT 25°C, Room RH = 55% Outdoor is at 40°C and RH 50%. And 10% by mass of air supplied to the buildings is out door. If the air supplied to the space is not to be at a temperature lower than 18°C. Find (i) Miu amount of air supplied to space in m/sec. (ii) Mass flow rates of return air, exhaust air and out door air (i) Capacity, BPFand sensible heat factor of cooling coil. Given: Condition DBT RH Sp. Humidity Enthalpy °C g.w.v./kg d.a. kJ/kg d.a. outside 40 50 23.6. 100 inside 25 55 10.6 52.5 supply Specitic valume of air supply point 0.836 m³/kg, coil ADP=9°C. 18 41.2
i need the answer quickly
"You did calculations using the simplified HAZ time-temperature formulas, assuming 3D heat flow, and are presenting your final internship conclusions to management. You realize with horror, in the middle of your presentation, that you forgot to label your calculated curves (below). Which curve is which? Pick the best answer A: "Plot 1 is HYPERFILL® and Plot 2 is p-GMAW. Since HYPERFILL® has the higher heat input, it cools more slowly." B: "Plot 2 is HYPERFILL® and Plot 1 is p-GMAW. Since HYPERFILL® has the faster travel speed of the two processes, it cools faster." C: "Plot 1 is p-GMAW and Plot 2 is HYPERFILL®. Since p-GMAW has the slower travel speed, it cools more slowly." D: "Plot 2 is p-GMAW and Plot 1 is HYPERFILL®. Since p-GMAW has the lower heat input, it cools faster" Both (A) and (D)
Please show all step, not Ai generated.
2-D: A fin may be manufactured as an integral part of a surface by using a casting or extrusion process, or it may be separately brazed or adhered to the surface. From thermal considerations, which option is preferred? 2-E: What is the difference between steady-state and transient heat transfer processes? Give an example for each of them. 2-F: What is the physical interpretation of the Biot number? 2-G: For flow over a flat plate, sketch variation of local convective heat transfer coefficient, h(x), versus the distance along the plate x for laminar, transition, and turbulent flow regimes.
Problem 1 A hot water pipe is used for domestic applications is insulated with a layer of calcium silicate. If the insulation is 25 mm thick and its inner and outer surfaces are maintained at Ts,1 = 800 K and Ts,2 = 400 K, respectively. The outside diameter is 0.12 m. Given the thermal conductivity calcium silicate insulation equals to 0.09 W/m.K. A. Define the difference between lagged and unlagged pipes. B. Calculate the heat loss per unit length for this pipe.