Course: Electrical EngineeringSubject: Electrical ApparatusInstructions:• Write the GIVEN with their respective symbols and units.• Do not skip the SOLUTIONS, do it step-by-step with their respectivesymbols and units• Round up to 3 three decimal places the FINAL ANSWERS and BoXit.Problem:The primary current to an ideal transformer rated at 3300/110 V is 5 A.Calculate:A. the turns ratioB. the kVA ratingC. the secondary current.

We need to analyse the given transformer .

Answered: Problem: The primary current to an…

Problem: The primary current to an ideal transformer rated at 3300/110 V is 5 A. Calculate: A. the turns ratio B. the kVA rating C. the secondary current.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: A 200/100 V, 50 Hz transformer is to be excited at 40 Hz from the 100 V side. For the exciting…

A: Excitation current = E/X

Q: In a transformer having a 10 to 1 ratio, the copper losses in the primary are 15 per cent less than…

A: The transformer problem can be solved easily.

Q: L1 R1 R1 L2 N1:N2 12 Lm Rc V1 V2

Q: The eddy current loss in a 2300 V, 60-Hz transformer is 280 W. What will be the eddy current loss if…

Q: 1. A 2.4-kVA, 2400/240-V, 50-Hz, the step-down transformer has the following parameters: : RH =…

A: Rated kVA is kVA.Induced EMF ratio is V.The high voltage to low voltage winding turns ratio is…

Q: DC 200 V is applied to the primary of a transformer with a conversion ratio of 1/5. From secondary…

A: The winding functions as a short circuit through the source terminals of DC when a DC voltage is…

Q: A Transformer has turns ratio of 2:15. When the secondary turns is 300, what is the primary turns?…

A: Given, For a transformer the turns ratio is N1N2=215 And the secondary turns is N2=300

Q: Determine the peak-to-peak ripple and dc output voltages in Figure 2. The transformer has a 48 V rms…

A: Step 1:Step 2: Step 3: Step 4:

Q: type of Transformer in dc machine

A: solve above ques.

Q: Transformer 1) Enumerate the way/s by which the voltage of the large coil may be: a) increased (AC…

A: The voltage in a coil is given by V= -L(di/dt). So for an ac source the voltage of a coil is…

Q: 2. The short-circuit secondary current in a transformer is 2 A. What is the primary current if the…

A: Given, A transformer has, Short circuit secondary current I2=2 A. Transformer turns ratio a=25.

Q: The primary of a current transformer takes 1 A at a power factor of 0.4 when it is connected across…

A: Given: N1=2N2Io=1 Acosϕo=0.4I2=50 Acosϕ2=0.8 lag

Q: The table below shows some performance parameters of a certain power transformer. Full-load voltage…

A: In this question we need to find a voltage regulation for the given condition.

Q: dabull (CME 446) 1 If F3=0.1 and Z3=45 Q, then the impedance of the next stage in the multi-section…

A: Given: Γ3=0.1Z3=45 Ω

Q: A single-phase transformer has a voltage ratio on open circuit of 7900/660 V. The primary and…

A: Transformer: It is a static device that is used to step up and step down the voltages.

Q: 10kva single transformer has turns ratio of 300 / 23.

A: The equation of the transformer is given as

Q: In an ideal transformer having a 1 to 2 turns ratio, the secondary: O a) current is half the primary…

A: In case of ideal transformer, transformer used for transfer the power and stepping up and stepping…

Q: Q6. Specification/Range of Power Supply:

Q: In the transformer circuit below, a load of 2.5cis 20° Ohms is connected to the output terminals of…

Q: What is the difference between a step-down and step-up transformer? Give one instance for each where…

A: Step up transformer : Transformer is electrical device which transfer electrical energy from one…

Q: (d) Assuming zero core reluctance, calculate the magneto-motive force (mmf) produced by the primary…

Q: a buck converter, what are the benefits and disadvantages if the changes of duty cycle is drastic…

A: Duty cycle : Duty cycle in the power system is defined as the ratio of the time during which a load…

Q: 1. An ideal 200W transformer has an input current of 2 A and an output voltage of 120 V. Determine…

Q: öialg äbäi A 220/1100 V transformer takes no- load current of 5A and absorbs 200 W. What is no load…

A: In this question , single phase transformer is given...No load current is given..No load losses…

Q: A step-up transformer is designed so that the output of its secondary winding is 2,200 V (rms) when…

A: Given: A step up transformer is designed to have V1=210 VV2=2200 V

Q: The open-circuit voltage of 240V and the full load secondary voltage of 220 V, then the % regulation…

A: The open-circuit voltage of 240V the full load secondary voltage of 220 V, then the % regulation of…

Q: Q2/The primary of a certain transformer takes 1 A at a power factor of 0.4 when it is connected…

A: TRANSFORMER: The transformer transfers power from one circuit to another circuit without a change…

Q: An ideal transformer is rated for a maximum power of 10VA.With a 10642 load and an unkownsource…

A: We need to find maximum load .

Q: AC power of 100 volts and 1 ampere enters a transformer with 2 coils and exits the transformer with…

Q: If the turn ratio of a step-down transformer is 30:1 and the no-load primary current is 1.25 A, the…

A: Given: Transformer primary turns, n1= 30 Transformer secondary turns, n2= 1 No load primary current…

Q: Given

Q: Draw the scheme of a single-phase transformer with two secondary windings and mark the main symbols…

Q: An ideal transformer with a turns ratio of 2:7 is fed from a 240 V supply. Determine its output…

Q: Q3/A/ The equivalent circuit impedances of a 20-kVA, 8000/240 V, 60-Hz transformer are to be…

Q: Figura 3-Transformador V. Ned Ns Vs Input Output

Q: 1.) A transformer with a rating 600 KVA has an efficiency 0f 94 percentage at full load and at 1/4TH…

Q: Determine Rz for a 12 V Zener regulator is used with a dc input of 20 V, a load current of 65 mA,…

A: determine Rz for a 12V Zener regulator is used with a DC input of 20V, load current of 65mA and a…

Q: Which of the following are power losses that can occur in a practical transformer (non-ideal)?…

Q: The primary winding of a 50-Hz transformer has 480 turns and is fed from a 6400-V supply. Determine…

Q: A power company supplies power to a small town that is 10 km away from the nearest substation. The…

A: The above question is based on the power system transmission network.To transfer impedance from one…

Concept explainers

Single Phase Transformer

A single-phase transformer is a type of power transformer. It is an electrical device that accepts converts the single phase alternating power into single phase alternating power. In this power conversion the voltage is stepped up or down. If the voltage is stepped up, the current will be stepped down and if the voltage is stepped down, the current will be stepped up.

Question

Course: Electrical Engineering
Subject: Electrical Apparatus
Instructions:
• Write the GIVEN with their respective symbols and units.
• Do not skip the SOLUTIONS, do it step-by-step with their respective
symbols and units
• Round up to 3 three decimal places the FINAL ANSWERS and BoX
it.
Problem:
The primary current to an ideal transformer rated at 3300/110 V is 5 A.
Calculate:
A. the turns ratio
B. the kVA rating
C. the secondary current.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

a)The voltage per winding of 220V/12V, 60 Hz single phase core transformer is 1V. If the maximum flux density in the core is 1.5 T, which of the following is the cross-sectional area of the core in cm²? 0.0030 0.0060 30 25 50 0.0050 0.0025 60 b) The voltage per winding of 220V/12V, 50 Hz single phase core transformer is 2V. If the maximum flux density in the core is 1.5 T, which of the following is the cross-sectional area of the core in cm²? 0.0030 0.0060 30 25 60 0.0050 0.0025 50
Can you answer this?
Draw the scheme of a single-phase transformer with two secondary windings and mark the main symbols and quantities. Write the formulas to determine the total power P1, the transformation ratios and the primary current I1.
A short circuit test performed on a 25 KVA 2300/230 V transformer gives the measured value of the resistance as 0.8 Q and 0.009 Q on the two sides of the transformer. The total equivalent resistance in Q referred to LV side will be
can i get some help
Needs Complete typed solution with 100 % accuracy.
The maximum efficiency of a 200KVA, 6000/230volt, 50HZ, single phase transformer occurs at half load and is 95% at unity power factor. What is the full load efficiency at 0.7 power factor?
P:11) Solve all parts.
In a transformer that has 10 times more turns on the secondary side (side 2) than on the primary side (side 1), the magnitude of the voltage/EMF across the windings on the secondary side, E₂ will be... O a.... 10 times lower than the voltage/emf on the primary side, E₁. O b.... the same as the voltage/emf on the primary side. O c.... always zero regardless of the voltage on the primary side, E₁. O d.... 10 times higher than the voltage/emf on the primary side, E₁.
3. An ideal transformer with a 500 turns primary and 125 turns secondary windings delivers 400W to a 40 load. The resistance of the primary windings is 160. Find the primary current and voltage.