Problem oneTwenty-four voice signals are sampled uniformly and then time-division multiplexed. Thesampling operation uses flat-top samples with us duration. The multiplexing operationincludes provision for synchronization by adding an extra pulse of sufficient amplitudeand also us duration. The highest frequency component of each voice signal is 3.4 kHz.(a) Assuming a sampling rate of 8 kHz, calculate the spacing between successive pulsesof the multiplexed signal.(b) Repeat your calculation assuming the use of Nyquist rate sampling.

Hello student Greetings The above question deals with the concept of time-division multiplexing…

Problem one Twenty-four voice signals are sampled uniformly and then time-division multiplexed. The sampling operation uses flat-top samples with us duration. The multiplexing operation includes provision for synchronization by adding an extra pulse of sufficient amplitude and also s duration. The highest frequency component of each voice signal is 3.4 kHz. (a) Assuming a sampling rate of 8 kHz, calculate the spacing between successive pulses of the multiplexed signal. (b) Repeat your calculation assuming the use of Nyquist rate sampling.

Problem one Twenty-four voice signals are sampled uniformly and then time-division multiplexed. The sampling operation uses flat-top samples with us duration. The multiplexing operation includes provision for synchronization by adding an extra pulse of sufficient amplitude and also s duration. The highest frequency component of each voice signal is 3.4 kHz. (a) Assuming a sampling rate of 8 kHz, calculate the spacing between successive pulses of the multiplexed signal. (b) Repeat your calculation assuming the use of Nyquist rate sampling.

Computer Networking: A Top-Down Approach (7th Edition)

7th Edition

ISBN:9780133594140

Author:James Kurose, Keith Ross

Publisher:James Kurose, Keith Ross

Chapter1: Computer Networks And The Internet

Section: Chapter Questions

Problem R1RQ: What is the difference between a host and an end system? List several different types of end...

See similar textbooks

Similar questions

Q15/ Channel 1 of Six channels PAM system handles 1KHZ signal. Channel 2 handles 2 KHz signals, channel 3 handles 3 KHz, channel 4 handles 6 KHz and channel 5 handles 6 KHz and channel 6 handles 25 KHz. The six channels are sampled at equal intervals of time using very narrow pulses at the lowest frequency that is theoretical adequate. The sampled signals are time multiplexed and passed through a LPF before transmission. a. What is the minimum clock frequency of the PAM system? b. Find Tx and Bx? c. What is the minimum cut off frequency of LPF used before transmission that will preserve the amplitude information on the output pulses? d. What would be the minimum bandwidth if these channels were frequency multiplexed, using AM technique and SSB technique?
Problem 2 In a DSB-SC system, the carrier frequency is 5 kHz and the message signal is given by m(t) 2cos1000nt + sin2000nt. Find and sketch the spectra of the message signal and modulated signal. Identify the upper sideband (USB) and the lower sideband (LSB) spectra in the DSB-SC modulated signal. Determine the average power in the message signal as well as in each frequency component of the modulated signal. Problem 3 The modulating signal m(t) = cos1000nt cos3000nt is multiplied by the carrier c(t) = cos(2nfct), where f. = 5 kHz. Determine and sketch the spectra of the modulating and modulated signals. Identify the upper sideband (USB) and the lower sideband (LSB) spectra in the DSB-SC modulated signal.
b- Design a sequence detector of the pattern 0100 where the circuit accepts a serial bit stream "x" as input and produces a serial bit stream "z" as output. Whenever the bit pattern "0100" appears in the input stream, it outputs z = 1: at all other times, z = 0, Overlapping occurences of the pattem are also detected, %3D
Please do question 15
. Given the function: F(a, b, c) = (a + b)’c + a b c’ + a c a) Create the truth table for function F. 7b) Implement F by means of an 8-to-1 Multiplexer using block diagrams. Implement F by means of a 3-to-8 Decoder using block diagrams and any gates if needed.
Assume we want to find the best match between an EEG signal and a sinusoidal waveform. • EEG sample frequency was 50 Hz. Generate two sin waves with frequency at 14 Hz and 20 Hz. We limit these shifts to 360 sinusoids, each having 1° difference in phase shift. Calculate the Rxx of these two signals at different phases. We will have to shift the sine wave over the EEG signal to find the best match between the two signals.
a)There should be a half-line difference between odd and even fields in a TV system using interlaced scanning. How is this made possible in practice? b) In a certain country where the power supply frequency is 60 Hz the horizontal oscillator frequency of the monochrome TV system (with interlaced scanning )used was found to be 15.75 kHz. Calculate the no. of lines per frame, the vertical oscillator frequency and the no. of frames per sec. c) The following two frequencies (f1 and f2) are related to ionospheric sky wave propagation : f1 =27 MHz , f2 = 9 MHz. One of them is the maximum frequency returned by the ionosphere when the waves are transmitted vertically upwards, and the other is the maximum frequency returned by the ionosphere at zero take-off angle. (a) Name these two frequencies f1 and f12. (b) Also calculate the height of the F layer for these pair of frequencies. Assume that the radius of earth (R) is 6371 km. (Answer the question in separate sheet, scan and upload along…
need the solves asap plz
Sch
Implement the following function with a8-to-1-line Multiplexer with threeselection lines? Draw the truth table and the corresponding block diagram for the MUX?F(A, B, C, D) = Σm ( 1, 3, 4, 11, 12, 13,14,15 )