PROBLEM O9: Two cast-iron pipes are held together by a bolt, as shown in fig. The outer diameters of the two pipes are 50mm and 70mm and the wall thickness of each pipe is l0mm. The diameter of the bolt is 15mm. What is the maximum force P this assembly can transmit if the maximum permissible stresses in the bolt and the cast iron are 200MPA in shear and 150MPA in tension, respectively? P

Q: A 4.8ft-long steel wire of 1/4in-diameter is subjected to a 750lb-Tensile load. Knowing that…

A: Concept: We will find the elongation of the wire due to applied load using the formula for…

Q: i- The Mechanical system shown in Fig. 4 is called? ------ Fig. 4. a- Symmetrical Mechanical system.…

A: (i) Answer = (b) Two force member Since in two force member the line of action of force will always…

Q: hollow cast iron column with the cross section shown in the image attached is subjected ti a…

A: A vertical point load acting at A of magnitude 100kNTo determine the maximum compressive and tensile…

Q: A E 6 m 4 m 4 m B P₁

A:

Q: 3. The figure as shown below is a rigid bar which is supported by two rods and a pin support. If the…

A:

Q: B F 12 ft 8 ft 8 ft 12 ft 12 ft E G 12 ft 12 ft 1200 lb 1200 lb 1200 lb

A:

Q: HW A rigid Sslab weighing boo Ku is Placed uPon two bronzevads and one Steel Vocd Cach of bo00 mm²…

A: Given data, Weight = 600 kN Area of bronze rod Ab = 6000 mm2 Coefficient of expansion for steel αs =…

Q: he bolt and its head are circular in cross-section with diameters as shown. hey are made of a…

A: Allowable force is generally the maximum stress that can be safely applied to a bolt structure.…

Q: Ql: A steel bur 25 mm diumeter is loaded as shown in fig. Determine the stresses in each part and…

A: Given data in question  Length Diameter  Elastic modulus  Loads To find out  Stresses Elongation

Q: The member shown in the right side consists of the steel rod AB that is screwed into the end of the…

A:

Q: A compound bar, 1.5m long is made up of three concentric square components A, B and C, fitted…

A:

Q: Determine the force in the most stressed bolt of the group shown in figure (2) using the elastic…

A:

Q: For the continuous beam shown in Figure 1, draw the internal force diagrams. You must accompany your…

A: Given Data:

Q: Cg Methed f Sectins loo kw determine forces in FE, FC bC ノ

A: Hello dear this is the solution of your problem The answer is found to be Force in members…

Q: 5 beam with the 75 mm wide flange at the bottom. Determine the moment of resistance of the section…

A: To determine the moment of resistance for given permissible stresses in tension and compression.…

Q: .B + sodb 30 lb CROSS. SECTION

A: Normal stress: it is defined as the stress that is induced when the member is loaded by axial force.…

Q: The plates in the figure below are each 3 inches by 0.5 inches in cross section. If the hole in each…

A: Solution:- Given information: Cross section of plate =3×0.5 in Hole diameter, d=1316 in, and Load,…

Q: 3. An aluminum bar having a cross-sectional area of 0.25 sq. in. carries the axial loads applied at…

A:

Q: 1. A steel rod of 20 mm diameter passes centrally through a copper tube 40 mm external diameter and…

A:

Q: hown in the figure. The properties of the segments and the work ble. Determine the maximum allowable…

A: Solution: For  compound bar (Steel section) Ast=0.75in2Est=30×106 psiLst=2×12=24…

Q: What is the cracking moment of the beam having a cross section shown in Figure 1 if f ‘c = 28 MPa?.

A: Cracking Moment- Cracking Moment is the moment beyond which the concrete begins to crack.When the…

Q: Q1:If allowable stresses are o, 165MPa.0, 100MPa = 70MPa determine max. value of W. M 300mm Im 4m Im…

A:

Q: Part A shown construct an equilibrium equation that relates the axial load in the steel and…

A: Uniform distributed load, Length of all post, Diameter of steel post, Diameter of aluminum post, To…

Q: Axial loads are applied to the compound ro composed of an aluminum segment rigidly connected between…

A:

Q: 10/10 find the shear stress in bolt in pin A 60 kN 4 M 3 BOLT DIA 20 MM A 50 kN PIN A 636 MPa O 159…

A:

Q: The structure shown below is hinged to fixed supports at A and C. The bars are each 4 in. by 4 in.…

A: Introduction- A structural support is a component of a building structure which contains the…

Q: Part A If the bolt is subjected to a compressive force of P = 21.9 kN, determine the magnitude of…

A: Length of bronze and steel rod is same.The change in length of steel is equal to the change in…

Q: Five plates with thickness t are bolted together by a bolt with diameter d. Which of the following…

A:

Q: A solid brass E 100 GPa axial member is loaded and supported as shown in the figure. Segments (1)…

A:

Q: In the figure shown, determine the normal stresses at AD + and BC + , shearing stress at bolt D • ,…

A: From the figure : Taking the moment at C: ∑Mc=0200.25+0.4-RD0.4=0Simplifying the above:RD=32.5 KN…

Q: 12 ID 12 Draw the Mohr's circle. Find the stresses on the plane shown. Fill in the blanks and table.…

A:

Q: : Fig. 2 shows a rod consisting of three segments, each having a circular cross- sectional area, is…

A: The answer are given in step by step format  Formula used - Stress = Force / Area

Q: Gusset plate Column Pin diameter = Steel plate Pin 80 mm 16 mm 10 mm thickness one 40 kN For the pin…

A: Determine 1. Normal stress acting on the gross area. 2. Normal stress acting on the net area. 3.…

Mechanics of Solids

It is the study of the behavior of solid materials, their characteristics under various circumstances such as variation in external forces, temperature, and other internal factors. It is one of most important study in the field of engineering science, especially chemistry and mechanical engineering. In rigid body, the idealization of the solid body in which deformation is neglected. Deformation is known as the force acting on the solid state system which exerts change in its shape of the body but it continues to be at rest or in a uniform motion but it cannot accelerate. But those solid systems do have elasticity, compressibility and can be bent. This field is very vast since there are wide range of materials around us.