Problem Number 3: In the given truss, determine the magnitude of the axial load and type of the indicated members in the table below. Member Magnitude, KN TYPE АВ ВС CF 145 KN 1.20 m 1.20 m 1.20 m 1.60 m 1.60 m 1.60 m 1.60 m 1.60 m. 1.60 m 120 KN 140 KN 125 KN 135 KN

Q: Create a 3-dimensional isometric projection based on the 2-dimensional orthographic projection below

A:

Q: Determine how far is the centroid of the given cross section above the base. + 4.50" 2-50" 4: 50"…

A:

Q: What is ZABC if FB of line AB is 40° and BB of line BC is 280°?

A: Given that :-FB of line AB = BB of line BC = To find the

Q: Map distance=5 cm Ground distance%3D2 km Determine scale

A: Given data : The value of map distance=5 cm The value of ground distance=2 Km   To find: Scale of…

Q: Write Penman equation flowchart to calculate ET= K.ET, - Κ.ΕΤ

A: Penman equation flowchart to calculate ET=K.ETp as follows

Q: Determine  static indeterminacy

A: Given data : Number of external support reaction (R)=2+1=3 Number of member in truss structure…

Q: How stadia interval factor is determined?

A: The Stadia interval: The Stadia interval is defined as the ratio between the focal distance between…

Q: What is seismogram?

A: A seismogram can be defined as it is the graphical record, which is generated by a seismograph. It…

Q: Why is GCMS considered a 3D analytical technique?

A: It stands for Gas chromatography - mass spectrometry. It is a method for identifying different…

Q: Area of the Triangles are denoted by the following formulas: 1. Basic Formula, A = 12 * base*…

A: Given: From the figure, AC=1690.54 m

Q: 10

A:

Q: The following statements about vertical curves is TRUE, except? O A. The value of the algebraic…

A: - A. Sag curves, where change in grade is positive for example valleys. On other hand, crest curves…

Q: How to make a conformal meshing for a multibody part?

A: There are two conditions for a conformal mesh. The intersection between any two elements is a…

Q: only typing

A: This question is related to Engineering mechanics from Civil Engineering Given -  Equation y=5-6x…

Q: Draw projections of the following two points A & B on the same XY line. Keep a gap of 50 mm between…

A: The figure or view shaped by joining, in right succession, the points at which these lines meet the…

Q: Calculate the Minimum X distance on the drawing below: 1.000 C Ø.995-1.000 +0.008MABC X O…

A: Given, Elevation and plan drawing of a section   To find : Minimum value of 'X'

Q: Find the areal scale for the following 3cm+09km

A: Given: Map distancex=3 cm Ground distanceX=9 km To find: Areal scale

Q: What is the stadia interval factor?

A: The Stadia is a technique for quick distance measurement using a telescope and a graduating rod. The…

Q: Distinguish first angle orthographic projection from third angle orthographic projection

A: Orthographic projection: The representation of an object by using the two-dimensional drawings in…

Q: Draw the isometric view given the orthographic views.

A:

Q: Discuss about NAVD88?

A: Answer Introduction A geodetic reference system is a system that is used to measure the correct…

Q: X100 + 200 + 250 + 300 35. x400 x450 x350 250 +300 x 500 x400 150 500 Soo e contour lines for the…

A: Here C.I is 50 meters

Q: Explain the difference between serpentine and helical scan recording.

A:

Q: Explain oblique angle of projection

A: oblique angle of projection- it is a graphical projection with parallel line which is used to…

Q: 1. What command do you use to display AutoCAD Point Style Box? (KIND/ DDPTYPE/ DS) 2. What is the…

A: Answer 1=> The Point Style window will open with a list of available point styles if you type…

Q: Practical part: Q5) Draw the profile with horizontal scale 1:1000 and vertical scale 1:20, stations…

A: Given : Stations and their Elevations in metres. Horizontal scale = 1:1000 Vertical scale = 1:20…

Q: In the map of contour lines below, which two points are the same height? a) I-I OB) IV-V OC) I-I OD)…

A: Given- A contour map-

Q: 3. у" — Зу' + 2у %3D 2x2 |

A:

Q: How did you get 36 in "(3 x 66 x 36)" and the 70.5 in "(29 x 3 x 70.5)"?

A: Data Given: t = 3 mmb = 165 mmc = 29 mmd = 72 mm Asked: How did you get 36 in "(3 x 66 x 36)" and…

Q: Q3. Please define the surveying terms below. Mean Sea Level (MSL): Datum: Elevation: Geoid:

A: It is required to define- Mean Sea Level (MSL) Datum Elevation &  Geoid.

Q: Determine the x- and y- coordinates of the centroid of the given area. 65m 105mmi 40mm -- 240 mm

A:

Q: Determine the x- and y-coordinates of the centroid of the shaded area. 470 125 60° 310 60 155 235…

A:

Q: ive one application of inversing in surveying.

A: to find  height of a particular point above the line of sight, then the inversing comes to picture…

Q: What are zenith angles?

A: The angle formed by the sun and the vertical is known as the zenith angle.

Q: 3 / 5 \times 11 / 4 \text { inches } \times 3^{1 / 6}

A: To find:- Multiplication

Q: 16m 8m 60° 126m 120m 20m 64m 16m

A:

Q: Find the centroid of the shaded area in the attached file 3cm Зст 1cm 3cm 1cm

A: Schematic diagram of the given problem:

Q: Draw the missing view. exact scaling not needed

A: Since you have posted multiple subparts We will solve only the first four.... Kindly repost the…

Team Management

To complete a specific task or to accomplish organizational goals along with increasing work productivity, individuals need to come together and think along a common path and direction. There are certain tasks in an organization that cannot be done alone and the involvement of more individuals is essential. These groups of individuals who work together for a common goal compose a team and the individual members involved are known as team members.