Problem No. 4. The frame shown is supported by a shear pin (diameter, d, ultimate shear Tu in ksi) and by a tie-rod AB. Both the tie-rod and the pin are to be sized with a factor of safety of FS = N (see table), Properties are listed on the table. Determine the diameter dr of bar AB if W is 10 kN. Also, determine the diameter p of pin at C. Yield Ultimate Strength Stress of of the rod the pin, is σΥ, GPa Factor of SET L1 L2 L3 Safety, N Tu, GPa 1.75 m 3.00m 1.50 m 3.00m A 0.50 0.34 3.0 2.5m В 0.75 0.45 2.75 2.5m C 0.65 0.50 2.8 2.00 m 3.00m 2.5m

Problem No. 4. The frame shown is supported by a shear pin (diameter, d, ultimate shear Tu in ksi) and by a tie-rod AB. Both the tie-rod and the pin are to be sized with a factor of safety of FS = N (see table), Properties are listed on the table. Determine the diameter dr of bar AB if W is 10 kN. Also, determine the diameter p of pin at C. Yield Ultimate Strength Stress of of the rod the pin, is σΥ, GPa Factor of SET L1 L2 L3 Safety, N Tu, GPa 1.75 m 3.00m 1.50 m 3.00m A 0.50 0.34 3.0 2.5m В 0.75 0.45 2.75 2.5m C 0.65 0.50 2.8 2.00 m 3.00m 2.5m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Draw M,N,T diagram
Given the 10m-grid elevations, find the volume, Simpson 3/8 (3d Degree). 096 0.94 0.93 0.93 -0.95 0.96 0.95 094. -0.79 -0.29 -0.98 0.98- -0.96 0.95 0.93- -0.16 0.32 -1.01 -0.99 -0.97 1.00 -0.44 0.54 -1.03- 1.00 0.98 1.04 -1.02 0.97 -0.98 -1.01 1.01 -0.99
Determine the lk and I, for the plane & shaded region. Dimensions 7,5 in inches 3
solve
Determine the y-coordinate of the centroid of the shaded area shown. 12" Parabolic 2" 0 Answer: y = i 10" -Xx in.
Xc - 3.884 Уст! Locate the centroid (XC, YC) with respect to X-Y axis X 2 4cm 4-5 8cm 6cm 3 cm
18" 2. 10 K- 2" 12" Find the centeraid, C=
400 N 600N 3m 3m
Problem Question 1: No. Determine the reactions at the supports for beams, frames and trusses structures below: 1(a) |SAN 18 EN 2 kN-m 500 600 mm 600 mm 600 mm mm
Q1. Draw the plan and components of the given line diagram. Assume necessary any suitable data. W, Bed W, 4 x 3.0 m 4 x 4 m D, W D, Hall D V 2x2 m 2 x 2 m D, 4 x 6 m Kitchen D, Wi 4x 3 m W. D, W D-1000 x 2000 mm, D, - 900 x 2000 mm, W - 900 x 1200 mm, W,- 2000 x 1000 mm, V- 800 x 300 mm. nswer:
A thin circular rod is supported in a vertical plane by a bracket at A. Attached to the bracket and loosely wound around the rod is a spring (spring constant K = 3lb/ft) and unreformed length equal to the arc AB. An 8-oz collar C that is not attached to the spring can slide without friction along the circular rod. Collar is released from rest when teta = 30 degrees. What is the maximum height above point B reached by the collar? (Non-anonymous question O)