Problem No. 4. A compound shaft consists of two pipe segments has the following properties: SET Segment Segment 1 Segment Segment 2 Torque TB 2 Outside wall Torque TC 1 outside wall diameter thickness diameter thickness A 400 mm. 12.5 mm 320 mm 10 mm 81.35 kN.m 28 kN.m 25 kip-ft 65 kip-ft 88.20 kN.m 34 kN.m В 12 in 0.365 in 8.0 in 0.280 in C 400 mm 10 mm 230 mm 15 mm Determine the magnitude of the maximum shear stress in segment 2. (1) Tc (2) В

Problem No. 4. A compound shaft consists of two pipe segments has the following properties: SET Segment Segment 1 Segment Segment 2 Torque TB 2 Outside wall Torque TC 1 outside wall diameter thickness diameter thickness A 400 mm. 12.5 mm 320 mm 10 mm 81.35 kN.m 28 kN.m 25 kip-ft 65 kip-ft 88.20 kN.m 34 kN.m В 12 in 0.365 in 8.0 in 0.280 in C 400 mm 10 mm 230 mm 15 mm Determine the magnitude of the maximum shear stress in segment 2. (1) Tc (2) В

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

x Question: The diameter of shaft used in the below design is 90 mm. Identical pulleys are used in the design with a radius of 160 mm. The forces acting on the system are defined as follow: F₁ = 1P kN; F₂ = 8P kN; F3 = 2P kN; F₁ = 6P kN; F5 = 4P kN; F = 7P kN. Employing the maximum shear stress theory, calculate the maximum permissible P for a safe design experience. L₁ = 1.4m; L₂ = 1.8 m; L3 = 1.4m; L4 = 1.6 m; allow = 75 MPa (allowable strength, σs) A F₁ F₂ L2 m F4 B 3 F6 Fs
Do please
Design a hallow shaft (Diameter and length) that develops 80 kW of power while rotating at a speed of 4000 rpm. The design constrains are as under:The angle of twist not to exceed 0.200Shear stress is not to exceed 480 MN/m2The outer diameter is to be twice the inner diameter. The shaft length is to be three times the outer diameter. Modulus of rigidity = 79 GN/m2.
Micro Bh Micros Bb Micros - с * Question Completion Status: Question 2 2.0 d=1.50 in. dia. 1.9 1.8 Class r = 0.08 in. The figure below show a stepped shaft in torsion. Compute the maximum shear stress at the step when it rotates at 100 rad/s and transmits 5000 lb-in/s. Use CamScanner app or Notes app of iPhone to scan all hand-written pages into one PDF file. Attach the PDF file here to answer in this question. Class ( bbhosted.cuny.edu/webapps/assessment/take/take.jsp?course_assessment_id=_2374 Class D = 2.00 in. dia. r= Fillet radius Class G Cuent Projec suntur Et WA AS hp
Q2: A rotating steel shaft shown: camied by bearings A and E. Machined surface. S - 500 MPa, reliability is 90%, r-3 mm. What is the life of the shaft if design factor 3? 100 100 - 300 15 kN 200- A 304 3rB -3r 35 450
Please give Handwritten solution use torsion equation
year 5,6 S Shaft Length 18.45 mm diameter 2.5mm -> diameer geor 5 → 14.72 diameter gear 6-) 6.16 ангрит spaed n= 8.49 грм our pult power H= 0.53 W input power H = 1/w Torque = 0.0378 N.m Find Maximum shaft stress i
The steel (E-30x10° Ib/in?) shaft shown in the Figure is to be designed for a critical speed not less than 1068 rpm. Determine the smaller diameter d (in inches) needed if d; =1.25d, 4=33 in., L2= 11 in., L3=27,5 in. and W= 1957 Ib. (Gravitational acceleration=386 in/s2). L1 L3 W d, d
100 kip 10 kip -ft The 4-in. diameter shaft shown above is made from a ductile brass alloy. Which of the following are closest to the principal stresses in the shaft? O01 = 31.8 ksi 02 = 76.4 ksi O 01 = 94.0 ksi 02=-62.1 ksi O 01 = 14.3 ksi %3D 02 = -6.37 ksi O o1 = 7.96 ksi !! 02 = 9.55 ksi
A shaft made of steel receives 7.5 kW power at 1500 r.p.m. A pulley mounted on the shaft as shown in Fig. has ratio of belt tensions 4. The gear forces are as follows : F, = 1590 N; F, = 580 N Pulley Gear F1 A D F, -100 : 200- 100→ All dimensions in mm. Design the shaft diameter by maximum shear stress theory. The shaft material has the following properties : Ultimate tensile strength = 720 MPa; Yield strength = 380 MPa; Factor of safety = 1.5.
Only HAndwritten answer please
The sbaft shown overhangs a bearing on the right and has the following dimensions: a - 5 in., b - 4 in., and - 10 in. The material is AISI C1040. annealed. This shaft is subjected to a torque T 10,000 in-lb., forces F - 10,000 lb. and F, 20,000 lb. Using a atatio-design approach, determine the diameter D for N 2.5, with eomputa- %3D Answer: a) Dia. = _inches %3D %3D %3D tions from the maximum shear stress theory. Note: Use Sy = 48,000 psi F2 N M