PROBLEM NO. 2: P. 1A mm I- 16 mm Two plates each with thickness t 16mm are bolted together with 6 - 22mm diameter bolts forming a lap connection. Bolt Spacing are as follows: S, = 40mm, S2 = 80mm, S3 = 100mm. Bolt S, S, S S2 diameter = 22mm. Use A36 steel. Calculate the allowable s,-40 strength due to block shear only. S,=100 S,-40 40 80 80 40

Q: Steps or Procedure in using Castigliano's First Theorem and some examples. Please answer asap! thank…

A:

Q: A steel tire has a dimensions indicated in the figure below. At 78 degrees Celsius, the said tire…

A:

Q: rigid beam is being supported by three suspender bars made of bronze and loaded as shown in the…

A: Given a rigid beam is being supported by three suspender bars made of bronze and are subjected to…

Q: difference between finite element analysis and finite element method

A: The finite element method is generally a numerical technique used to perform finite element analysis…

Q: 3. Five weights of 10, 20, 30, 40, and 50 N rest on a table with the coordinates (0.5, 15*), (2,…

A:

Q: Y = Ya + Snyw

A: Given data in question  Bulk unit weight  Dry unit weight  Degree of saturation  Unit weight of…

Q: : Prove that (1) Ya = Gs Yw 1+e

A:

Q: 4m B 3m 28 KN/m 6m D 4m

A:

Q: Find the work done Force 20 N displacement=0.33 m

A: Given Force, F = 20N And displacement, s=0.33m Workdone,W = F*s=20*0.33 = 6.6 Nm Hence Workdone is…

Q: The cantilever beam geometry shown is made from steel E=200GPA. Determine the deflection and the…

A: To calculate the value of slope and deflection at point B, using the double integration method. In…

Q: Im 2m

A:

Q: • Part A Replace the loading system acting on the beam by an equivalent resultant force and couple…

A:

Q: Determine the value of Force

A: we know that W = F x S Therefore, F = W/S    = 40/5    = 8N

Q: What reduction factor are we going to use if p > Pb a. 0.9 b. 0.65 c. 0.45 d. Ø= 0.65 +0.25 Ey Et…

A: Given:-ρ>ρbTo find:-reduction factor

Q: find the second derivative in its simplified form 4. y= e^4x - e^-4x  /  e^4x + e^-4x

A: Consider the given equation y=e4x-e-4xe4x+e-4x Calculate the derivative of given equation…

Q: Q2. Fit a polynomial and find C @T-0 T -50 -20 10 70 100 C 0.125 0.128 0.134 0.144 0.15

A: The above answer has good explanation

Q: Find the force applied Work done=20 J Displacement=3 m

A: To express this concept mathematically, the work W is equal to the force f times the distance d, or…

Q: If the resultant of the two forces and couple M passes through point 0, determine M. 150 mm M 150 mm…

A: Consider the free body diagram,

Q: Q D1 D2 D4 L1 D3 L2 L4 Find out the following? Case 1: Major Losses only H = Case 1: Minor Losses…

A:

Q: Q1: - Determine the centroidal coordinate of the shaded area shown in the figure below. Assume all…

A: ##CENTROIDAL Coordinates of Shaded Area ####

Q: 30 m 54 mm 48 mm 54 mm 72 mm A thin, homogeneous wire is bent to form the perimeter of the figure…

A: Wire is bent to form the perimeter of figure aboveCentre of gravity of wire with respect to x,y =?

Q: ood 0.56 m x 0.56 m x “h” meters in dimension was thrown into a liquid with SG = 2.078. It floats…

A: VOlume oftotal brickV=0.56×0.56×hVolume of brick inside SG=2.078V1=0.56×0.56×h-0.29Volume of brick…

Q: A block of wood 0.25 m thick is floating in sea water. The Specific Gravity (SGw) of Wood is 0.35…

A:

Q: differential equation using bernoulli y' + y = y^-2

A:

Q: 1 The figure shows a metal hanging by a thin wire from a floating wood block. The wood block has a…

A:

Q: ose that A 3.2 m. (Figure 1) Determine the magnitude of the resultant force of the two forces acting…

A: Given : To Find : FR , Alpha , Beta and Gamma?

Q: roid (7, g) of the area showr

A: Note : we can solve first three part for you according to bartleby guidelines  Given:- a = 27 cm b…

Q: An experimental device imparts a force of magnitude F = 48 lb to the front edge of the rim at A to…

A: Given data  Find moment about O and B. (Counterclockwise positive) Find d distance from O to C…

Q: Tf = c' + o'n * tan o' Tf=? ; c'= ? ; o'n=? ; q'=?

A:

Q: (b) Figure 5 shows a timber column and several forces acting on it. As an engineer, you were…

A: Given , F1= 250N F2= 500N

Q: Let Q = 0 and T = 6 (Example: 4QT mm2 = 406 mm2). Just substitute the number in letter. Thank you!…

A: Given data: P1=50 kN P2=86 kN  Cross-sectional area of each bar= 406 mm2 It is required to determine…