• Problem No. 1 • The bar ABCD in the figure consists of three cylindrical steel segments with different lengths and cross-sectional areas. Axial loads are applied as shown. Calculate the normal stress in each segment.

Q: 4) For a simple pendulum, the graph will be between I and T? curve parabola Straight line hyperbola

A: Pendulum time period formula T=2πlg

Q: When calculating "I", why have you used 50^3 x 24 rather than 24^3 x 50?

A: You have asked, When calculating "I", why have you used 50^3 x 24 rather than 24^3 x 50?

Q: H. What scale is used if a line 84 mm long represents a fence 63 m long?

A: Given:-  Scale length = 84 mm Actual length = 63 m = 63000 mm  To Find:-  Scale

Q: 30° A 60

A: According to the given data  A load 340 N is carried by the rope A and B  We need to find Tension in…

Q: A symbol used to identify a physical feature of a part as a datum feature is called a: O Reference…

A: Reference feature: There are the feature where the other features are referenced from. feature…

Q: fis increasing on ( a, b) if f´(x) equal O less than and equal O greater than and equal O less than…

A: By using the increasing decreasing function  If f'(x)>0 for x in (a,b), then f is increasing.

Q: Given the concurrent force system below, the x-component of the 600N-force is

A: Given data Given figure

Q: 2.3. Outrigger

A: Given Data: Diagram of an outrigger

Q: Convert the octal number 23228 to its hexadecimal number equivalent, (base-8 to base-16).

A: Steps of Conversion: The simplest way is to convert the octal number into a decimal, then the…

Q: where are the graphs?

A: Given data in the related question: Maximum speed = vf = 183.58 mi/hr Distance travelled = 5 mi Time…

Q: Draw the orthographic views of the following isometric figure.

A:

Q: Draw the orthographic views of the following isometric figure

A: Given  3D model isometric view To find Orthographic view

Q: What is the period in seconds?

A: To determine: The time period for the swing, where it takes approximately 2 seconds to reach on side…

Q: What is the allowance between "C" and "D"?

A: Allowance: The difference between the maximum material limits of the two mating parts is defined as…

Q: Give all the location dimensions between the datum target areas , A1 and A2. X = _________________,…

A: Give all the location dimensions between the datum target areas , A1 and A2.X =0  ,  Y =74   ,   Z =…

Q: 2 ft 2 ft 3 ft A 6 ft

A:

Q: It's known that the mechanism is a 4-bar

A: Drawing the kinematic diagram of the mechanism as shown below, (a) Calculating DOF: DOF can be…

Q: In a slider crank mechanism (schematic shown the figure), the crank rotates at 60 revolutions p…

A:

Q: 250 pound/cubic feet = O a. 4804 kilogram/cubic meter O b. 44.2 kilogram/cubic meter O c. 4004…

A: Solution: One Pound = 0.453592kg One feet= 0.3048m   Therefore…

Q: Q3: Chose and mark a datum point on the given work-piece (shown in figure 1) and mark out the…

A:

Q: question: The degrees of freedom of the calculation package in the figure?

A:

Q: A 25 ft long solid steel rod is subjected to a load of 10,000 Ib. This load causes the rod to…

A: Data given -  L = 25 ft = 25 × 12 P = 10000 lb  ∆L = 0.477 in  E = 30 × 106  psi

Q: Number of links? The value must be a number 8 Number of full joints (J1)? Figure 2 Figure 2

A: Given mechanisms,

Q: . Convert the decimal number 35710 into its binary number equivalent.

A: Given: A decimal number is, (357)10 .

Q: An aluminum plate 20 feet by 40 feet is to be divided by 32 equal pieces 5 feet x 5 feet plate by…

A:

Q: Create a table showing wrench sizes in metric and U.S. units.

A: Following are the wrench sizes in metric and U.S. units.

Q: the p-value 42,45,38,37.5 ,41 40.5,45,36,37.5,39

A:

Q: Do number 13.12

A: Given Data Qr=24000 BTU/hr EER=11 Cost= 14 cents per kWh

Q: Figure 5 shows the rod AB rotates clockwise and has an angular velocity and angular acceleration of…

A: Note: Since you have posted a question with multiple sub-parts, we will solve the first three…

Q: Datum feature symbols shall not be applied to centerlines only

A: Datum feature symbol is indicated with the help of either a white or black triangle. Letter…

Q: UNITS: INCHES MATERIAL: ALUMINIUM -R.75 0.3 4.00 4.00 3.5 0.3 2.0 0.3 0.75 0.75 2.3

A:

Q: 2.5 m

A:

Numerical Calculations

In the mid-20th century, the availability and the growth in power of digital computers led to the increase in the mathematical model in the field of engineering and science. The analysis of these detailed models needs to be increased.