Problem II. The midpoint B of the steel cantilever beam ABC is -Aluminum supported by a vertical aluminum rod. Find the maximum allowable 5m value of the applied force P if the stress in the rod is not to exceed -Steel 120 MPa. Use Est = 200 GPa, I = 50 x 10° mm for the beam, Eal = 70 GPa, and A = 42 mm² for the rod. B A %3D 2 m

Problem II. The midpoint B of the steel cantilever beam ABC is -Aluminum supported by a vertical aluminum rod. Find the maximum allowable 5m value of the applied force P if the stress in the rod is not to exceed -Steel 120 MPa. Use Est = 200 GPa, I = 50 x 10° mm for the beam, Eal = 70 GPa, and A = 42 mm² for the rod. B A %3D 2 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: = constant 5. Bernou lli's equation is expressed as asY'2g Research on the corresponding units por…

Q: A -3 m B -3 m IC + -3 m- 60 kN m

Q: Consider the cantilever beam shown in Figure 2, which is subjected to a linearly distributed…

A: Slope and deflection at free end Deflection δδ=WL430EISlope θθ=WL324EISubstituteDeflection at free…

Q: A circular steel rod AB of diameter d1,length L and modulus of rigidity G is loaded as shown is…

Q: A beam of square cross section (k =length of each side) is bent in the plane of a diagonal (see…

Q: The unit load method used in structural analysis is (A)Applicable only to statically indeterminate…

A: To find the correct answer-

Q: 3. Prove that the Poisson ratio (v) is almost always less than 0.5.

A: Poisson ratio is defined as the ratio of lateral strain to linear strain. It is always less than 0.5

Q: B. A beam subjected to a uniformly-distributed load has a: Choices: First-degree shear curve…

A: A) Here, there is a twist in the question, it is not asked the Representation of the change in the…

Q: 1. A beam element with length L = 10.0 m is used in a finite element analysis and the displacement…

A: mx..+cx.+kx=0 m=mass c=damper k=spring constant Mg=F [self-weight] F=kx [Spring force] F=cx. Given,…

Q: Jacobi and Gauss-seidel methods only work if the coefficient matrix of a given system of linear…

A: Given, The Question is about two methods, Gauss and Jacobi- Both Jacobi and Gauss Seidel come under…

Q: At a certain instant, the velocity of cylinder B is 2 ft/s down and its acceleration is 0.5 ft/s2…

Q: III. Solve using Algebraic substitution: 1.

A: Given:-

Q: Fourier series: simply supported beam deflection under trapezoidal load

Q: 6...

A: If you have further doubts about this. I will be happy to help you solving this. Thank you!

Q: Find the laplace transform for the equation f(x) = 3e^-5

Q: Below presents a continuous beam with A being fixed and B is pinned and C has a roller. Take: E =…

Q: detail the uniform distributed load

A: To determine the uniformly distributed load matrix

Q: A beam ABCDE is shown below: B D A E The ratio of kinematic indeterminacy of the beam if considering…

Q: B my and M

Q: 1. Beam ABC is supported by a pin at A and a roller at B. It is subjected to a concentrated load P…

A: Given Data Find (a) The equations of the elastic curve. (b) The deflection at C. (c) The location…

Q: A 2nd degree polynomial (x) has values 2, 5,12, at x = 0, 1, 2 respectively. The integral f(x) dx is…

Q: Determine by the method of nodes, the forces at which all the members of the following trusses work.…

A: In a given figure, a truss is shown, it is required to find the forces in each member of truss.

Q: 4. Briefly describe shape functions for finite elements. If a truss element has the end node…

Q: For the figure shown, determine the following: a.) The moment of the force 300 N at points A and B…

A: In mechanics, the force evaluation is divide into force and moment. forces or reaction at any point…

Q: The following may be used in getting the resultant of forces except: A Square Rule B Triangle Rule…

A: Correct option is a) Square rule

Q: whereas the flexural rigidity of the secO

A: formula using P0LAE=60-RaK0

Q: Given that the Laplace transform of te-kt is F(s) = (s+k)² Laplace transform of t²e³t without using…

A: Given values: L(te-kt) = 1(s+k)2Here, f(t) = te-ktFs=1(s+k)2

Q: A circular steel rod AB of diameter d, length, Modulus of elasticity E and modulus of rigidity G, is…

A: Given-A Circular steel rod AB, Diameter =d, Length= L, Modulus of elasticity= E Modulus of Rigidity=…

Q: Select the correct statement among the following? a. Maxwell Reciprocal theorem states that in any…

Concept explainers

Matrix Algebra for Structural analysis

Structural analysis is a process in which the effects of different loads and internal forces, acting on structures and their elements are determined. This method of analysis is effective in detecting the failure loads of the structural elements and the design can be altered before commencing the construction process, which ensures proper strength and safety of the structures.

Question

please solve only using CONJUGATE BEAM METHOD

Problem II. The midpoint B of the steel cantilever beam ABC is
-Aluminum
supported by a vertical aluminum rod. Find the maximum allowable
5 m
value of the applied force P if the stress in the rod is not to exceed
-Steel
120 MPa. Use Est = 200 GPa, I = 50 x 10° mm* for the beam, Eal = 70
B
A
GPa, and A = 42 mm? for the rod.
–2m-
- 2 m -

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 9 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Please help. This problem involves maximum allowable stress. Thank you.
how to solve this one fast please
P1=50kN P2=80kN
The midpoint B of the steel cantilever beam ABC is supported by a vertical aluminum rod. Find the maximum allowable value of the applied force P if the stress in the rod is not to exceed 120 MPa. Use Est = 200 GPa, I = 50 x 106 mm4 for the beam, Eal = 70 GPa, and A = 42 mm2 for the rod.
Determine the maximum tensile and compressive bending stresses developed in the beam shown. The cross-section has the given properties. NA 1-35 x 10mm a. RA = b. RE= c. fb(c) = d. fb(T) = 80 mm 200 mm A 1.5m kN KN 5kN m MPa MPa B 1.5m SkN/m 2m 5KN n 2m 4
Please help:
NO TRUNCATION IN THE MIDDLE OF SOLUTION AND COMPLETE SOLUTION PLEASE. Thank you A wooden beam AB supporting two concentrated loads P has a rectangular cross section of width b = 100 mm and the height h = 150. The distance from each end of the beam to the nearest load is a = 0.5 m. the span of the beam is 5 m. Determine the maximum permissible value P (in kN) if the allowable stress in bending is 11 MPa (for both tension and compression) FINAL ANSWER IN 3 DECIMALS
1) will upvote anyone who will answer correctly. thanks
Knowing that a factor of safety of 3.0 is required, determine the largest load P that can be applied to the steel structure shown. Member AB has a 50 mm x 50 mm square cross section. Use Yield Stress &,= 250 MPa. B both pin ends 30° 1.2 m BA,
P1=58kN P2=80kN
Problem 1 Please choose the correct answer and also write down your solution. (1) The beam is subjected to the shown loading. What is the correct statement regarding the flexural stress at A and B? P P a. Both og and og are tensile stress. 0.5 m 0.5 m 0.5 m b. Both oa and og are compressive stress. Og is tensile stress and og is compressive stress. с. d. OA is compressive stress and og is tensile stress. A В (2) The cantilever beam is subjected to the load P and has cross section as shown. What is the ratio of the magnitudes of the maximum tensile and compressive flexural stresses over the a-a cross section? b. 3/7 a. 7/2 d. 2/10 е. 3/10 h. 10/3 c. 7/3 f. 10/2 i. 1/1 g. 2/7 250 mm 20 mm 60 mm 200 mm 2 m 1 m 15 mm 15 mm
1. The assembly is shown is attached to supports at A and D. Section BCD is a solid 2" diameter aluminum [E = 10,000 ksi] rod. Steel [E = 30,000 ksi] tube AB has an outer diameter of 3.50" and a wall thickness of 0.216 in. Determine (a) the stresses is sections AB, BC and CD, and (b) the deflections of joints B and C. [OAB = 3.40 ksi (C), Osc = 5.863 ksi (T) Oc, = 4.959 ksi (C), 8, = 0,0054"– , d. = 0,02975"→] %3D %3D %3D %3D 13 kips 17 kips A C 13 kips 17 kips 4 ft 5 ft 5 ft