Problem I. The beam has a loose fit built-in support at B which allows the end of the beam to rotate through the angle O, = 0.75° when the load is applied, as shown in the detail. E= 72 GPa and I= 120 x 10°mm*. Determine the following: a. Reaction at A (kN) | 200 kN -2 m -2 m b. Moment at B (kN m) c. Slope at A in radians A B B d. Displacement at the application of 200kN load Detail

Problem I. The beam has a loose fit built-in support at B which allows the end of the beam to rotate through the angle O, = 0.75° when the load is applied, as shown in the detail. E= 72 GPa and I= 120 x 10°mm*. Determine the following: a. Reaction at A (kN) | 200 kN -2 m -2 m b. Moment at B (kN m) c. Slope at A in radians A B B d. Displacement at the application of 200kN load Detail

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

can someone give an example problem of this with solution.
Solve using: (Complete Solution) A. CONJUGATE BEAM METHOD B. VIRTUAL WORK METHOD Determine the deflection at point C of the beam shown. E = 200 GPa. I = 250(10^6)mm^4.
The bending stiffness of the beam given in the figure is constant and EI is given.a) Draw the elastic curve of the beam by defining the elastic curve.b)Obtain the elastic curve equation by using at least two of the Integration, initial values, Mohr and cantilever beam methods.. Compare the results, explain your reasons for using the methods.c) Calculate the rotation at point A and the collapse value at z = L.
For the beam shown,(1) derive equations for the shear force and the bending moment for any location in the beam. (Place the origin at point A.)(2) use the derived functions to plot the shear-force and bending-moment diagrams for the beam. Specify the values for key points on the diagrams. Let , , , and . Derive the equations and construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions. For all answers, use the sign conventions for shear force and bending moment as detailed in Section 7.2
Solve for RA, RB, MA using Double Integration Method
A beam of square cross section (d =length of each side) is bent in the plane of a diagonal (see figure). By removing a small amount of material at the top and bottom corners, as shown by the shaded triangles in the figure, we can increase the section modulus and obtain a stronger beam, even though the area of the cross section is reduced. (a) Determine the ratio y defining the areas that should be removed in order to obtain the strongest cross section in bending. (b) By what percent is the section modulus increased when the areas are removed?
Problem 1: A nonuniform beam is simply supported at both ends. The flexural rigidity of the left part equals EI, whereas the flexural rigidity of the second part equals (s+1)EI where's'is your serial number. (a) Use K functions to derive the characteristic equation; (b) Solve for the characteristic equation to derive natural frequencies. Report the results. (s+4)EI EI L/2 SERIAL NUMBER= 2
Obtain the formula for the deformed beam shown below. Indicate the location of where the maximum deflection occurs and its value.Also obtain the deflection at point C and the rotation at point A for the beam using (a) the moment area method and (b) the conjugate method.
solve this problem on the finite element method;
If you wanted to find the y-centroid of the shape below using the volume element shown, you would need to express the length Lin terms of y. O True O False
9) This is a fictitious beam of the same length as the real beam, but it is externally supported and internally connected. a. Cantilever Beam b. Virtual Beam c. Imaginary Beam d. Conjugate Beam