Problem: Determine the centroid and moment of inertia about the centroidal axis of the shaded area shown. Use the tabulation shown. 2" 3" 5"

Q: LESSON: AUTODESK AUTOCAD Choose from the choices:

A: The broken line is used to draw the large drawings which are not possible to draw on the sheet,…

Q: Sketch the figure using AutoCAD and hatch the lines with colours . mention the dimesions as shown in…

A:

Q: 4. Find the x and y reactions at the pins at A - D and Find the Tension in the cable at the motor.…

A: Find the x and y reactions at the pins at A - D.Find the Tension in the cable at the motor.

Q: The beam AB is homogeneous and has a mass of 5,191. The tension in the cable of the crane can not…

A:

Q: re 2) mine the smallest allowable diameter of the roc able bending stress is allow = 225 MPa.

A: Apply the moment equilibrium condition about point A.The force equilibrium condition along the…

Q: The symbol, , means: O diameter O circle O all around left side

A: To choose: The correct answer. Concept used: Engineering drawing symbol: In engineering drawing,…

Q: Problem 1: a) Draw the free body diagram of the member ABC? b) Determine the reaction forces at the…

A:

Q: A thermometer reading 18oF is brought into a room where the temperature is 70oF; 1 minute later the…

A:

Q: Double acting cylinder cannot be used as a single acting cylinder. Select one: O True O False

A: Single Acting cylinder as it were expands by weight from a pump and after that withdraws by the…

Q: The figure shows a cylindrical shell very long, of length L, very internal radius large r1, outer…

A: The figure shows a cylindrical shell very long, of length L, very internal radius large r1, outer…

Q: Write F if True and T if False. Lithosphere is also called Earth's crust

A: Answer: The given statement is True-F.

Q: a. Which of these observations would you use to serve as data to šupport your claim? The b. Do you…

A:

Q: The figure shows a shaper machine that uses Whitworth quick return mechanism wherein the different…

A: Given Data OA=75cm OP=50cm CA=150cm CD=135 cm

Q: y h с b bh .1

A:

Q: "Sarcomere"

A: option b) part between two Z line

Q: L t C Determine the moments at fixed ends 'a' and 'd' ?

A:

Q: FORTUNE FAVOURS THE BRAV

A: A week ago our little villa was invaded by fear-based oppressors. There was dread in the seniors.…

Q: Convert the decimal number 11510 into its octal number equivalent

A: Convert Decimal to Octal with Steps Write the given decimal number. If the given decimal number is…

Q: Respond with TRUE if the symbol of the valve shown below is drawn correctly. 1 3. 9 TypehereIG 2.

A: Correct option: True.

Q: Given the front, top and side views of the drawing add the missing lines (center, object, and…

A:

Q: Generally, the triangles can be divided into two kinds; right angle and not right angle. * O True O…

A: It is true that the triangles can be divided into two kinds; right angle and not right angle.

Q: Q.1) Knowing that the tension in cable BA is 570 N, determine the moment about O. Neglect the…

A:

Q: What is Line J? ARROWHEAD .35mm A 7.0 В

A: Solution:

Q: Determine the sequence for the following figure

A: Given: To find: Sequence

Q: What is the meaning of + S.F, -S.F, +B.M and ?- B.M

A: There are sign convention for shear force and bending moment.  The shear force at a cross-section is…

Q: Create a table showing wrench sizes in metric and U.S. units.

A: Following are the wrench sizes in metric and U.S. units.

Q: Z is incorrect

A:

Q: if the bullet that hit the cashier made a bullet hole that was 3 mm wide and 8 mm long, white was…

A: Given data:

Q: Which is figure depicts the ideal diesel cycle processes? Caipr rejeto. V3=Uz B. C S.

A: Ideal diesel cycle is combustion process in IC engine which comprises the four process to complete a…

Q: can you draw the FBD

A: There are four rivets in this problem. In ideal case load will be equally distributed. Each rivet…

Q: Interpret the significance of the letters shown in the illustration

A: Instruction given at tail of the welding symbol is "See detail A".Here detail A will have the…

Q: From the following identify the true statement. O In general safety precaution, the operator should…

A: In general safety precaution main motto is to stay safe and stay alive.. Operator should know how to…

Q: A Before Ater False True O

A: Suppose Mass of Ball (A) = Ma                  Mass of Ball (B) = Mb  Initial velocity of mass A is…

Q: Which corners would be visible from the FRONT orthographic view of this image. Select all that…

A: Front view will be like

Q: By and bx are labeled wrong

A:

Q: 01: Write G code to Write the first Letter of you name

A:

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.