PROBLEM 9 Water flows steady through the piping junction as shown below, as it enters section 1 at 20 gpm. The average velocity at section 2 is 1.5 m/s. A portion of the flow is diverted through the showerhead, which has 100 holes of 1- mm diameter. Assuming uniform flow through the showerhead, calculate (a) the flow rate at section 2, and (b) the exit velocity from the showerhead holes. o d. = 2 cm |e d: = 2 cm

PROBLEM 9 Water flows steady through the piping junction as shown below, as it enters section 1 at 20 gpm. The average velocity at section 2 is 1.5 m/s. A portion of the flow is diverted through the showerhead, which has 100 holes of 1- mm diameter. Assuming uniform flow through the showerhead, calculate (a) the flow rate at section 2, and (b) the exit velocity from the showerhead holes. o d. = 2 cm |e d: = 2 cm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 200mm nonstandard orifice is installed in 250mm pipe carrying water. When the flow is 165lit/sec, the mercury differential gauge reads 50mm. Compute the value of coefficient for the orifice meter.
Water at 40°C is flowing from A to B through the system shown in Fig. 11.22. Determine the volume flow rate of water if the vertical distance between the surfaces of the two reservoirs is 10 m. The elbows are standard. Flow 4-in coated ductile iron pipe Total length = 55 m 6-in coated ductile iron pipe Total length = 30 m Sudden enlargement Butterfly valve fully open 10 m
A pump draws water from a sump through a vertical 6" pipe. The pump has a horizontal discharge pipe 4" in diameter that is 10.6 ft above the water level in the sump. While pumping 1.25 cfs, gases near the pump at the entrance and discharge read -4.6 psi and +25.6 psi, respectively. The discharge gage is 3.0 ft above the suction gage. Compute the horsepower output of the pump and the head lost in the 6" suction pipe.Answer: 10.7 hp, 2.4 ft
Water flow through a venturi meter an inlet dia. = 100 mm and throat dia. =50 mm , P at inlet = 70 kpa. And at the throat 75 mm mercury, if the discharge coefficient = 0.95 , find the flow? %3D
FLUID MECHANICS!!! TY!
instant downvote for wrong answer
2. A Venturi meter having a diameter of 6 in. at the throåt is installed in a horizontal 12-in. water main. In a differential gage partly filled with mercury (the remainder of the tube being filled with water) and connected with the meter at the inlet and throat, what would be the difference in level of the mercury columns if the discharge is 5.0 cfs? Neglect loss of head.
Urgent please
Water flows at a rate of 17.0 e/s along a 100 mm diameter pipe AB, which branches at B into three pipes, BC and BD, which are 25 mm diameter and the third, BE which is 50mm diameter. If the flow rate in BE is 33% of BC, and the velocity of the water in BD is 5 m/s, find the discharges in each of the three branches.
Determine the discharge in pipes 1, pipe 2, pipe 3 and pipe 6 in the system shown if the total head loss from A to B is 100m and friction factor for all pipes is 0.02. a) Discharge in pipe 1 is _____cu.m./s b) Discharge in pipe 2 is _____ cu.m./s c) Discharge in pipe 3 is _____ cu.m./s d) Discharge in pipe 6 is _____ cu.m./s
A.Determine the velocity of flow in the pipe in fps. (Please round-off final answers to the nearest whole number) * B.Determine the discharge Q in ft^3/s. (Please round-off final answers to the nearest whole number) * C.How many feet above the center of the pipe will water stand in piezometer tube 3? (Please round-off final answers to the nearest whole number) D.How many feet above the center of the pipe will water stand in piezometer tube 4? (Please round-off final answers to the nearest whole number) *
7. Barometeric pressure is 101.3 kPa and vapor pressure of water is 32.4 kPa. Calculate the elevation (in meters) of the tubing end 3 for maximum flowrate through this pipeline. Also sketch the energy line, EL (color red) and the hydraulic grade line, HGL (color blue) on the drawing for this situation. El. 34 Water 150 mm d EI. 30.5