Problem 9: Approximate Analysis for Lateral Loads (Portal Method)

Q: A) Write the commands to draw shape (A) by using AutoCAD program. B) Write the Modified commands…

A: AUTOCAD is the application software used for drawing and drafting plans, designs and basic shapes,…

Q: Graph the resultant from the x-axis.

A:

Q: 1. Problem Solving: Solve the following situations as completely as possible, use any method that…

A: P= 250 KN W= -7x+81 KN/m Note According to the company guidelines i am able to answer only first…

Q: 2-18: A pelton wheel has a mean bucket speed of 10 m/sec with a jet of water flowing at the rate of…

A: Mean bucket speed (u1 = u2 ) = 10 m/s  Flow rate (Q) = 0.7 m3/sec Head (H) = 30 m  Deflection angle…

Q: A rectangular channel of 2.5 m width is carrying a discharge of 4 m³/s. Considering that…

A: Given- Width B=2.5 m, Discharge Q=4 m3/s, It is needed to find the velocity of flow at the critical…

Q: Form the figure shown, a flexible belt placed around a rotating drum of 4-inch radius acts as a…

A: Given  Radius of drum = 4 inch  Kinetic friction= 0.7

Q: Label the maximum and minimum values on the graph. d) Draw the internal bending moment diagram (BMD)…

A:

Q: 2. Determine the discharge of the weir having a head of 1.2 m in L/s a) If a 90° triangular weir is…

A:

Q: Two vertical forces, each of magnitude P- 24 kips, are applied to a beam of the cross section shown.…

A: On a simply supported beam hinged at A and roller supported at D, two-point loads of the same…

Q: Problem 5: Draw shear and bending moment diagrams and sketch the qualitative deflected shape for the…

A: A beam system is given in the figure belowNeed to Find Draw the shear force and bending moment…

Q: Get the centroid of the same figure (using 5 shapes only)

A: Given Required Centroid using 5 shapes only

Q: Q3. Determine the plastic moment Mp of the cross sections shown, assuming the material to be…

A:

Q: A B F C D 000 4₁ L₂ L3 Fishing line with a tensile strength of 50 lbs is used at B to fasten 2…

A: Tensile strength of fishing line (T) = 50 lbs Determine the maximum force F that can be supported.

Q: 4. A pipeline with diameter of 850 mm and length of 4.1 km connects two fresh water open reservoirs…

A:

Q: The framework shown in Figure 1 is supported by an A-ball joint and an E-roller. Neglecting the…

A:

Q: Situation #6 CE Board Nov. 2017 A cantilever beam projects 2.8 m from the face of a wall. The beam…

A: Given: X = 215 kN B = 1 kN/m E = 200 Gpa To find: 1) The moment at the fixed end 2) The shear at…

Q: From the given figure, determine the following characteristics of the resultant: (a) magnitude of R,…

A: Given Data: The length AC is given as 6 ft.   To Determine: (a) The magnitude of R. (b) orientation…

Q: An B m. long beam is on hinged at its left end and on fixed support at its right end. Its flexural…

A: Given data : X=212 B=1 Flexural capacity =610 kNm Web shear capacity =642 kN Flexural rigidity…

Q: Derive the expression

A: Expression for change in length of the block

Q: 2. A steel beam is loaded as shown in Figure 1 below. Determine the vertical displacement at point C…

A:

Q: If two closely coiled helical springs A & B with the mean diameter of spring A is half of that of…

A: If two closely coiled helical springs A & BEqual numer of active coilsSame wire diameter,Same…

Q: Let F = [F] N. k) Determine the reaction Ng at the roller B. A 350 N 1 m* 2 m Z D C 60° F 3 m 200 N…

A: Given data,  F = 204 N

Q: Q. No. 01 Find out the missing storm precipitation of station "C" given in the table 1 using station…

A:

Q: The tension member shown in the figure below is a ¹/2 x 10 plate of A36 steel: Fy = 36 ksi, Fu = 58…

A:

Q: Find the Normal Stress at points A, B, and C in the Rod below. Dimensions given are diameters. 1 in.…

A:

Q: A cantilever beam AB is fixed at its right end and extends L out of the edge of the pool. The board…

A: Given data in question  Cantilever beam Span L Point load P To find out  Moment equation Slope…

Q: The diameter of droplet is 0.075 mm. What is the intensity of the pressure (N/sq. cm) developed in…

A:

Q: What is the x and y - coordinate of the centroid.

A:

Q: Draw the shear and moment diagrams for the compound beam shown in the figure. Assume the supports at…

A:

Q: Q. No. 04 Compute the discharge in the stream based on the current meter measurements provided below…

A: Calculating the Velocity at 0.6 ft the depth using the formula: V0.6 ft=V0.2 ft-V0.8 ft2

Q: The diameter of a 3 meter pipe decrease aw the diameter profile at each 500 mm

A:

Q: Determine the centroid x and y

A:

Q: 20kN 2m 5m Draw and solve for the shear and bending moment diagram of the structure using Slope…

A: Jcjvk

Q: For the a" by a" frame of thickness t", break the area into two pieces, the entire frame and gap,…

A: To compute the moment of inertia of the frame about the x-y axes and the polar moment on inertia.…

Q: For the beam and loading shown in the figure below draw the Shear Force and Bending moment diagrams.…

A: Let, Horizontal reaction at A is HA. Vertical reaction at A an B is RA and RB respectively.

Q: A simply supported beam has a span of 20 ft. If the cross-section of the beam is as shown in Figure,…

A:

Foundation construction