Answered: Problem 770 If 140 L/s of oil flows…

Problem 770 If 140 L/s of oil flows through the system shown, determine the total head lost between points B and C Ans: 11.8 m El. 35 m A El. 5 m 300 mm El. 20 m 150 mm C

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A pump with an impeller diameter of 300 mm running at a speed of 2950 rev/min delivering 450 L/min of water at a head of 350 kPa is going to be replaced by a geometrically similar spare pump running at a speed of 1450 rev/min delivering the same flow rate and head. Determine the impeller size of the spare pump and the percentage increase (decrease) of power required for the spare pump. OL. 380.1 mm; a decrease of 61.33% OI., 380.1 mm; an increase of 38.77% I. 147.5 mm; an increase of 3.4% IV. 210.3 mm; a decrease of 83.1%
Reservoir A (Elev. 106 m.) to the turbine is connected by a 638 mm pipe. Another 638 mm pipe connects the turbine to Reservoir B (Elev. 85 m.). The loss of head from A to 1 is 5 times the velocity head of the pipe and the loss of head from 2 to B is 0.2 times the velocity head of the pipe. If water is being discharged at a rate of 741 L/s, determine the horsepower required for the turbine to operate. (Assume 100% efficiency.)
Q4: Assuming f-0.020, determine the discharge in the pipes. Neglect minor losses. Pipe Diameter AB 250 mm 200 mm 400 mm BC BD Length 1200 m 600 m 200 m EL.45m EL 3m. B C EL. 3.0m D EL 0.0m
The 600 mm diameter pipe conducts water from reservoir A (El. 61 meters) to a pressure turbine (El. 4.60 meters), which discharges through another 600-mm diameter pipe into tailrace B (El. 0 meter). The loss of head from A to the entrance of the turbine (pt.1 ) is 5 times the velocity head in the pipe and the loss of head from the exit of the turbine (pt.2) is 0.20 times the velocity head in the pipe. If the discharge is 708 Liters/second, Determine the efficiency of the turbine if the output power is 480 hp. a. 61.20% b. 69.15% c. 75.72% d. 86.88% e. 89.57%
A Borda's mouthpiece 200mm in diameter discharges water a head of 4m. Determine the discharge in liters/sec and the diameter of the jet at the vena contracta. Cv= 0.98, Cc=0.62
A storm drain has a maximum capacity of 120 L/min. During heavy rains, an influx of 240 L/min approaches the drain. Assuming the drain is cylindrical, by how much would the drain radius need to be increased to handle the heavier rainfall? Assume the water travels at the same linear speed in both drains. The answer is 1.4. Please explain why A 16 times greater B 42 times greater C 2 times greater D 1.4 times greater
For the system of pipes shown, the flow of water in pipe (3) is 25 L/s. Find: The flow in pipes (1) and (2): Q1 =……………….., Q2 =…………………. The difference in head between the two tanks is H =………………… f1:0.016 f2:0.028 f3:0.018
Water at 38°C flows from A to B through 244 m of average 300-mm-I.D. cast iron pipe (e = 0.00061 m).Point B is 9.1 m above A, and the pressure at B must be maintained at 138 kPa. If 0.222 m3/s is to flowthrough the pipe, what must be the pressure at A? Ans. 314 kPa (show the complete solution with diagram) [Note: Indicate the formula used in determining the friction factor. (Colebrook Equation, Haaland Equation, andor Swamee Jain Equation). If not given, Use properties of fluid based ontemperature available ontheinternet.E.g. (density, viscosity). Apply roughness of pipe values from https://www.pipeflow.com/pipe-pressure-drop-calculations/pipe-roughness]
6. A fabricated assembly made from three different sizes of standard steel tubing is shown below. The larger tube on the left carries 0.072 m3/s of water. The tee branches into two smaller sections. If the velocity in the 50-mm tube is 12.0 m/s, what is the velocity in the 100-mm tube? Ans. 7.88 m/s Reducing tee Flow 100-mm OD x 35-mm wall steel tube 160-mm OD x 5.5-mm wall steel tube 50-mm OD x 15-mm wall stoel tube
Q4: Assuming f-0.020, determine the discharge in the pipes. Neglect minor losses. Pipe Diameter AB 250 mm 200 mm 400 mm BC BD Length 1200 m 600 m 200 m EL.45m EL 3m. B C EL. 3.0m D EL 0.0m
Please don't copy the answer from the online pdf. I need explanation+diagram
If the water surface elevation in reservoir B is 110 m, what must be the water surface elevation in reservoir A if a flow of 0.03 m^3/s is to occur in the cast iron pipe. Use f= 0.0021 for all pipes. (DO NOT ROUND OFF)