A bolt needs to be tightened to a degree that is equal to a moment amounting to 60 N-mm. If a 14-inch cross wrench will be used, how much force should be applied on both ends of the wrench to tighten the bolt? If ϴ = 60 deg, find the following:a)x and y components of 900 lbb)x and y components of 500 lb PROBLEM 7. A bolt needs to be tightened to a degree that is equal to a moment amounting to 60 N-mm. If a 14-inch crosswrench will be used, how much force should be applied on both ends of the wrench to tighten the bolt?PROBLEM 8. If 0 = 60 deg, find the following:a) x and y components of 900 lbb) x and y components of 500 lb900 lbᎾ500 lbPx

Since the moment is given in N-mm and the length of the wrench is given in inches, we need to…

PROBLEM 7. A bolt needs to be tightened to a degree that is equal to a moment amounting to 60 N-mm. If a 14-inch cross wrench will be used, how much force should be applied on both ends of the wrench to tighten the bolt? PROBLEM 8. If 0 = 60 deg, find the following: a) x and y components of 900 lb b) x and y components of 500 lb 900 lb Ꮎ 500 lb P x

PROBLEM 7. A bolt needs to be tightened to a degree that is equal to a moment amounting to 60 N-mm. If a 14-inch cross wrench will be used, how much force should be applied on both ends of the wrench to tighten the bolt? PROBLEM 8. If 0 = 60 deg, find the following: a) x and y components of 900 lb b) x and y components of 500 lb 900 lb Ꮎ 500 lb P x

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Please solve in handwritten format quickly (show fbd and formula)
30 mm X1 A pair of pliers grips the bolt as shown below. B E 70 mm 30 mm 30 mm X2 X3 X4 Note: tan 0=y₁/X₂ 30 mm ₁ (a) For the input force, P, determine the force exerted on the bolt. (b) What is the mechanical advantage of this machine? (c) Suggest two ways that the mechanical advantage of this system could be increased.
Two plates are connected using three 20-mm-diameter bolts as shown in the figure. If the axial load P is 50 kN determine the shear stress in each bolt. 130 mm 25 mm Your answer: O 53 MPa. O 159 MPa O26.5 MPa O 79.5 MPa O 106 MPa: ooo 25 mm P
Three uniform 1-meter bars weighing "W" each are welded together as shown. The bars are suspended by three vertical wires. Bars AB and BC lie in the horizontal x-y plane, and the third bar lies in a plane parallel to x-z plane. If the tension at B is 250 N, determine the value of w (in kg) and the tension in A and C.
#1 will upvote anyone who will answer correctly. Correct decimal places please. Thanks
A crate with a mass of 250 kg is held in equilibrium by three ropes attached to a steel ring. a d3 d₁ d5 B A 5.5 m 4 m d2 3.5 m 2m d₁ Z 3 Values for the figure are given in the following table. Note the figure may not be to scale. Variable Value d₁ 2 m d₂ d4 a. Determine the magnitude of the force/tension in cord A, TA. b. Determine the magnitude of the force/tension in cord B, TB. c. Determine the magnitude of the force/tension in cord C, Tc. Round your final answers to 3 significant digits/figures. The magnitude of the force/tension in cord A is The magnitude of the force/tension in cord B is The magnitude of the force/tension in cord C' is d5 kN kN kN
Please answer the question correctly and pleaase put the answer on the paper. Thank you Note: The tolerance is ± 1 in the third significant digit. Put the exact answer
A plate is used as a bracket and is attached to a column flange as shown in the following figure. Use an elastic analysis and compute the maximum bolt shear force. 2 + N 4.1 3" 2" 3" 2" 0 0 O oo 40 k 27
A compound bar consisting of bronze, aluminum, and steel segments is loaded axially as shown in the figure. Determine the maximum allowable value of P if the change in length of the bar is limited to 2 mm and the working stresses prescribed in the table are not to be exceeded. E=200 GPa A=D300mm? L=3m 2m 2 m 3m 1.5m Match each tem to a choice
1. The figure below shows three cycles of time-varying loading on a double D-ring held together with a single bolt and nut, such as we have discussed in class. The figure shows both the bolt tensile force and the member compressive force. F, solid. F dot-dashed. 7000 6000 5000 4000 3000 2000 1000 t, time (a) Based on the figure, give the minimum and the maximum of the external load, P. (b) Based on the figure, give the stiffness coefficient of the joint and the pre-load. (c) Draw and annotate the force load diagram with F, and Fm on the vertical axis and P on the horizontal axis. (d) When the load is at Pmaz, determine the load factor with respect to joint separation. (e) Assume that the proof load, Fp, is 7500 lbf. When the load is at Pmaz, determine the load factor with respect to overproofing. Tmar:
1 A steel bar is 40 mm in diameter for a length of 100 mm, 30 mm in diameter for a length of 60 mm and 20 mm in diameter for the remaining 80 mm of its length. Calculate the load required to produce a total elongation of 0,177 mm in the rod. What would be the diameters of a steel tube of the same total length and same material subjected to a load of 70 kN to produce the same elongation, namely 0,177 mm. Assume a diameter ratio of 1,2 to 1 for the tube and let E = 210 GPa.
Please help, I promise to give good feedback. Please do not just guess. Thank you!