Problem 7:A brass weight is to be attached to the bottom of the cylinder made from auniform material with specific weight 6.46 kN/m³, so that the cylinder willbe completely submerged and neutrally buoyant in water at 95°C whichhas density of 9.44 kN/m³. The brass is to be a cylinder with the samediameter as the original cylinder as shown in the figure. What is therequired thickness of the brass?Water surfaceCylinderWaterat 95°C750 mmBrass plateY=84.0 kN/m1= ?450 mm diameter-

Answered: Image /qna-images/answer/62137433-4e7a-4883-be54-694fbea8edb3.jpg

Problem 7: A brass weight is to be attached to the bottom of the cylinder made from a uniform material with specific weight 6.46 kN/m3, so that the cylinder will be completely submerged and neutrally buoyant in water at 95°C which has density of 9.44 kN/m3. The brass is to be a cylinder with the same diameter as the original cylinder as shown in the figure. What is the required thickness of the brass? Water surface Cylinder Water at 95°C

Problem 7: A brass weight is to be attached to the bottom of the cylinder made from a uniform material with specific weight 6.46 kN/m3, so that the cylinder will be completely submerged and neutrally buoyant in water at 95°C which has density of 9.44 kN/m3. The brass is to be a cylinder with the same diameter as the original cylinder as shown in the figure. What is the required thickness of the brass? Water surface Cylinder Water at 95°C

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The bottom of a steel "boat" is a 7 m ✕ 8 m ✕ 6 cm piece of steel (ρsteel = 7900 kg/m3). The sides are made of 0.580 cm thick steel. What minimum height must the sides have for this boat to float in perfectly calm water? The side height should not include the thickness of the bottom. (Answer in cm, thanks)
Choose the correct answer
I need the answer as soon as possible
A weight, with an unknown mass, falls through a distance of 10 millimeters (mm) onto a collar attached to the bottom end of a vertical bar. The bar is 3 meters (m) long and has a cross-sectional area of 600 square millimeters (mm2). The impact causes the bar to instantly stretch by 2 mm. The Young's modulus of the bar material is 200,000 MPa. Determine: 1. The weight of the falling object. 2. The stress experienced by the bar due to the impact.
A blacksmith immersed a piece of steel at 600°F into a large bucket of water with a temperature of 65°. After 1 minute the temperature of the steel was 200°. How much longer must the steel remain immersed to bring its temperature down to 97°? The steel must remain immersed ☐ more minute(s). (Round to the nearest tenth as needed.)
Please include complete solution and free body diagram.
1 Proof that a solid aluminum block of 4 mm x 3 mm x 3 mm, such as shown in FigureQ1 (a), can float on water at 20 °C due to the effect of surface tension. The density ofthe aluminum block is 2700 kg/m3. Determine the contact angle. 2. A solid alloy cylinder having a diameter of 6.48 cm slides downward at a terminalvelocity of V through a vertical pipe. The downward motion is resisted by an oil filmbetween the piston and the pipe wall. Determine the oil viscosity when the velocityV is 5 m/s. The inner diameter of the vertical pipe is 6.5 cm, and the alloy density is3500 kg/m3.
A circular nylon [E = 8 GPa; ν = 0.35; α = 29 ×10-6/°C] disk with a circular hole in its center is shown. At an initial temperature of Ti = 22°C, the outer diameter of the disk is D = 210 mm, the diameter of the central hole is d = 55 mm, and the thickness of the disk is t = 24 mm. At a final temperature of Tf = 46°C, determine:(a) the change in diameter Δd of the central hole (assume an increase Δd as positive, otherwise as negative).(b) the change in thickness Δt of the disk (assume an increase Δt as positive, otherwise as negative).(c) the normal strain in the circumferential direction around the outside of the disk.
PROBLEM 4 For the figure shown, determine the stresses of the wires and the elongation when the temperature change is 45°. Aluminum 800 mm2 Steel 600 mm2 200GPA 11.7 micro m/m°C Area E 70GPA Coefficient of Linear 23 micro m/mC Expansion stel AL zm Im 20 kym
Please i need the answer as fast as you can
SITUATION. The figure shows a pellet about to be fired from a sling. The total unstretched length of the rubber is 60 mm. The rubber elongates 1 mm for every 15 N force. Length a=100 mm, b=40 mm. a
Q1/ A liquid has a specific weight of 59 lb/ft³ and a dynamic viscosity of 2.75 lb-s/ft². Determine its kinematic viscosity.