Problem 5.4. Determine the soil loss for a field at your present location if K 0.015, 91 m, s = 10 percent, C = 0.20, and upslope and downslope farming is practiced. What conservation practice should be adopted if the soil loss is reduced to 7 Mg/ha?

Q: y? = 2x and the line x - y = 0.

A:

Q: 1- find the area of the region lies above the line y = -x and inside the circle r = -3cose

A:

Q: The state of stress at a point in a member is shown on the rectangular stress element in (Figure 5)…

A: Step 1: Step 2: Step 3: Step 4:

Q: Q3) In the following section: a) Calculate the coordinates of the center of gravity 8 6.

A:

Q: Problem 2: Determine the centroid X-bar with respect to Y-axis -150 mm 15 mm C 150 m -15 mm 15 mm…

A:

Q: 150 mm Locate the centroid of the coloured area. 50 mm 100 mm 100 mm

A: Marking points over figure- A, B, C, D, E, F In the fig three shapes can be observed clearly- 1.…

Q: Determine the coordinates of the centroid of the trapezoidal area shown. Assume a = 310 mm, b = 570…

A:

Q: 2. Locate the centroid (x, y) of the cross-sectional area. 5 in 05i 0.6

A:

Q: A cube of edge 24mm is resting on the top of a frustum of cone of base diameter 60mm and top…

A: In the engineering graphics we can draw both the 2 dimensional projection and 3 dimensional…

Q: The bent rod shown below consists of two straight parts along x and y- axes and a half-circle in…

A: Given diagram:-

Q: R=6 cm T. 5 cm 2 cm 8 cm (a)

A:

Q: Q.: Find the coordinate of the centriod of the shaded area 4 Y 3 m-

A: Given, Equation y=2x-30.5

Q: y(V) – y = 0 1. y" – 10y' + 29y = 0 2. %3D

A:

Q: 1" 5" 2" 1-Determine the location of the centroid (x,y) of the centroid. 2- Determine the Ix0 and…

A:

Q: Determine the XT and YT a. Using the Top Most, Left Most Reference Line b. Using the Bottom Most,…

A:

Q: Get the centroid of the same figure (using 5 shapes only)

A: Given Required Centroid using 5 shapes only

Q: Compute y. (16 – 2 x 2.5) = 0.69 16

A: Given: γ=16-2×2.516

Q: dont understnad how in part 3. it was equal to 1201+480.51  how did we get the value of 1201?…

A: Note:- The previous answer of 1201+480.51 was wrong. Please find the correct answer.The width of the…

Q: Properties of moment of inertia of common shapes.

A: REFERENCE LINKS: https://engineeringstatics.org/MOI-common-shapes.html…

Q: Derive and show the relationship or transformation of e Kv> to V/v = Ite e Vs =

A: Void ratio e=VvVs Where Vv=Volume of void Vs=Volume of soil solid

Q: Determine the area and the centroid of the area if a=5.5 cm, b-12.8 cm, and c-6.5 cm. xy 2 b- Area:…

A:

Q: 3.24 The four forces are in equilibrium. Deter- mine F, and 0, (a) graphically from the force…

A:

Q: 35 R13, R8 42 12.5 20 R8 R9 15 34 26 25 44 17 OL 91 12

A: Handmade drawings are attached herewith.  Actual scale drawings files cannot be attached here like…

Q: Determine the x. Measure

A:

Q: Determine the x- and y-coordinates of the centroid of the shaded area. Input values only without…

A:

Q: Determine the X¡ and YT(using both a and b) a. Using the Top Most, Left Most Reference Line b. Using…

A:

Q: Locate the centroid x̄ of the area.

A: The given figure is shown below:

Q: Particular solution of (D³ + 12 D² + 36 D)y = 0, %3D

A: Differential equation: - It is defined as a mathematical equation which is useful to relate one or…

Q: The moment diagram by parts are base on the moment diagram of O Fully restrained beam O Cantilever…

A: Moment diagrams by parts is a method to solve the determinate beam and find reactions in beam.

Q: Find the x-coordinate of the centroid in 120 mm mm. - 60 mm - 40 mm 80 mm 60 mm

A:

Q: Find the centroid 20 30 25

A: A1=12×20×25=250 square unitA2=30×25=750 square unitA3=π×1522=353.43 square unit

Q: Find the volume of excavation required for the area shown in the figure. Each grid point (20 in…

A: Depth of the cut at every location is given find the average depth of cut…

Q: b (x+c)(x-c) A

A: To solve the expression (x+c)(x-c) step by step, we'll use the difference of squares…

Q: Locate the centroid ỹ of the area. -xy = ?

A: The equation of y is given by,

Q: How did you get FB=6072N? Because I am getting 5643.4N

A: Data Available Asked: Reactions FA and FB

Q: Find the centroid along x- axis of the shaded area. x - axis = mm. 40 165 105 40 240 Dimensions in…

A:

Types of Composite

Composite materials are formed by merging two components that have different chemical and physical properties. The merged output is termed as a composite, whose properties are completely different from the individual components. Composite materials also have better strength than the individual components.Composite materials usually have two main parts, reinforcement material, and matrix material. The matrix material acts as a binder and surrounds the fiber of another material that bears a much higher strength. This material is known as the reinforcement material. The matrix materials are usually high-strength additives resins, while the fibers of the reinforced material can be random, oriented, and in a mat format.Composite materials are also known as fiber-reinforced composite polymers because they are composed of the polymer matrix which is reinforced to laboratory-created fibers or naturally occurring fibers, such as glass fibers, carbon fibers, or aramid fibers. Under the application of external loads, the matrix material absorbs and transfers the loads to the fibers, these fibers in return provide good compressive strength, tensile strength, and stiffness to the fiber-reinforced composite materials.Depending upon the matrix and the reinforcement material, different properties can be induced to the fiber-reinforced composite materials, including good corrosion resistance properties. The most common matrix material is the resin while the glass fibers act as the reinforcement material. Strong fibers provide strength and stiffness to the composite materials while, a soft and flexible resin provides shape to the composite materials.