Problem 5.4-Lodate the ceritroid of the plan area shown by integration.

Q: y

A:

Q: The dot product of two unit vectors: (The answer cannot be found on the other choices.) always has a…

A: When the dot product of any two vectors is equals to 1 then those vectors are in same direction…

Q: (Determine the (f_y ) when force 80 Ib and angle 30° on the axis (X .A 40 .B 40lb .C 4lb .D 40N

A:

Q: Q1: Find the resultant force and the component force F for the system shown below (fig 1) using…

A: Calculated the resultant force and the component of force F for the system using parallelogram law.

Q: The region bounded by the parabola x = y² and y = x2 revolved about the y-axis to generate a solid.…

A:

Q: PO 8 in.

A: Redraw the following figure for the given question.

Q: Q3/ For the plate shown in figure below find (a) E A Y수 4 6 X 7 5

A: Let us consider the given figure , divide into two parts of area A1 and A2 The sum of area ΣA can be…

Q: h a 60° 60° --X

A: Let’s divide the shaded area into two parts. Section 1 is a triangle OAB and Section 2 is a circular…

Q: What is the maximum magnitude of the bending moment caused by force G? If none, enter zero. Do not…

A: It is required to determine the magnitude of the maximum bending moment by the force G.

Q: 2 m Find the angle theta. a = 5. b = 3. 1m 1m D

A:

Q: In the picture, a weight pulls on a pulley (solid disk) of mass 0.5kg and a radius of 0.25m. The…

A:

Q: Determine all furce mem bers of truss Shown the

A:

Q: 15 kN 20 kN 2 m m

A:

Q: The landing gear system of a plane is made of an actuator AC and 2 rods CB and OAB. They are pin…

A:

Q: The mass of casting is 120kg after 6% of its mass was machined off. Determine the mass of the…

A: The mass of casting is 120kg after 6% of its mass was machined off. Determine the mass of the…

Q: 400 Ib 14' A 60° 450 Determine the Value of P

A: given data: let  RA=normal reaction force at ARB=normal reaction force at B AC=4' CD=14' DB=2'

Q: Determine the x-y and n-t components of the 39-kip force F acting on the simply-supported beam. F =…

A:

Q: determine (a) the required value of a if the wn is to be vertical, (b) the corresponding 30° 200 N

A:

Q: Determine the angle 0 between the edges of the sheet-metal bracket. -400 mm 250 mm 300 mm 50 mm y

A:

Q: (Determine the (f_x ) when force 80 N and angle 30° on the axis (X .A 69N .B 69.28lb .C 69.28N .D…

A:

Q: Part A In Eigure ). w35 kip/ft. Folow the sign convention Delermine the shear force acting at point…

A:

Q: Fy = 16 kN O Fy = 4 kN O Fy = 2 kN O

A:

Q: For the rotational system shown in the fig- ure, write the equations of motion from which the…

A:

Q: Express the quantity 254,998m in mm.

A: To convert meter quantity into millimeter one must be familiar with the no. of mm exist in one…

Q: If A=0.375 inch, B=0.923 inch, C=1.0992 inches, find G A 기사 W -|×|-> G- -B- -C- F E-

A:

Q: In order to pull out the nail at B, the force F exerted on the handle of the hammer must produce a…

A: According to the question data MA=200lb.inclockwise   and the figure  We need to find Force F to…

Q: What is the direction of the edge formed between the intersection of (211) and (102)?

A:

Q: Find the center of gravity of the wire.

A: The centroid, when referring to a solid item, denotes the geometric center or the location where the…

Q: 3 ft us 4 ft < 1 of 1 B Determine the moment of the force F = {40i -35j + 20k} lb about the AB ax…

A:

Q: Q3/ For the plate shown in figure below find * (a) ΣΑ YA 7 9. X 8 5

A:

Q: Dotermine ali force truss Shown mem bers of thhe

A:

Q: Find the angle between the planes x + y = 1 and 2x + y -2z = 2

A: Write the expression to determine the normal vector of both the planes. Substitute the value of…

Q: A hollow tube with thickness t = 1/4 in. is applied with a tensile load of 33 kips. Compute its…

A: Given data,  Tensile load P= 33kips = 33000 lbs  t= 1/4 in  Tensile stress S= 12 ksi = 12000 lb/in²…

Q: Express:            50000mm3 as m3 3.5m3 as mm3 20m3 as cm3 45cm3

A:

Q: +y (i) +5 dx y cosx dx dy dx (m) dx (iv) dx

A: Degree &amp; Order: Order: highest numbered derivative in the equation Degree: highest power to…

Q: Determine the moment of 75 N force about point B in the figure shown below. 160 mm D a- 120 mm B 250…

A:

Q: Solve erf only

A: Given:To Find: the value of x.Note: In the above equation,