Problem 5.30 A 1600 kg car, when on a rectilinear and horizontal stretch of road, can go from rest to 100 km/h in 5.5 s. (a) Assuming that the car travels on such a road, estimate the average value of the force acting on the car for the car to match the expected performance. OE (b) Recalling that the force propelling a car is caused by the friction between the driving wheels and the road, and again assuming that the car travels on a rectilinear and horizontal stretch of road, estimate the average value of the friction force acting on the car for the car to match the expected performance. Also estimate the coefficient of friction required to generate such a force.

Problem 5.30 A 1600 kg car, when on a rectilinear and horizontal stretch of road, can go from rest to 100 km/h in 5.5 s. (a) Assuming that the car travels on such a road, estimate the average value of the force acting on the car for the car to match the expected performance. OE (b) Recalling that the force propelling a car is caused by the friction between the driving wheels and the road, and again assuming that the car travels on a rectilinear and horizontal stretch of road, estimate the average value of the friction force acting on the car for the car to match the expected performance. Also estimate the coefficient of friction required to generate such a force.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A spring is used to stop a 32 kg metal sphere which is moving down a 30° incline, as shown in Figure Q2(a). The spring has a constant k = 33 kN/m and initially compressed 50 mm. Given that the velocity of the metal sphere is 5.5 m/s when it is 5 m from the spring and the friction can be neglected. (Gravity g = 9.81 m/s?) Q2. (a) Determine all the kinetic and potential energy components at the initial (i) and final position of the metal sphere. (Let the x be the additional compression of the spring). (ii) Calculate the maximum additional deformation of the spring requires to bring the metal sphere to rest. (iii) Determine after the metal sphere come into rest will it rebound upwards the slope or not? if can how much it will move up again the slope until it temporary at reset otherwise stated the reason why the metal sphere would stay at rest. 5.5m/s m=32kg 5m 30 Figure Q2(a)
A 200-kg log is pulled up a ramp by means of a rope that is parallel to the surface of the ramp. The ramp is inclined at 34.5° with respect to the horizontal. The coefficient of kinetic friction between the log and the ramp is 0.870, and the log has an acceleration of 0.750 m/s2. Find the tension in the rope.
A cord passing over a pulley connects two masses, as shown, where m, = 3.00 kg and m, = 6.00 kg. The system accelerates with a magnitude of 1.31 m/s?. The coefficient of kinetic friction between the masses and the incline is the same for both masses. Assume the pulley is frictionless, and the cord is massless. (Due to the nature of this problem, do not use rounded intermediate values in your calculations-including answers submitted in WebAssign.) m2 m, 35.0° 35.0° (a) What is the coefficient of kinetic friction? 0.69 You have found the coefficient of static friction, but you are looking for the coefficient of kinetic friction. Draw free-body diagrams for both blocks and write Newton's second-law equations in the x- and y-directions. Condense your four equations into two by substituting, and solve the system of two equations for the two unknowns, u and T. (b) What is the tension (in N) in the cord? Draw free-body diagrams for both blocks and write Newton's second-law equations in the x-…
Figure 2 G 0.75 m A B 2 m 1.5 m Figure 2 shows a 2000 kg lorry with a center of mass at G. Starting from rest, the lorry achieves a speed of 15 m/s under a constant acceleration after it has traveled 100 m. The front wheels are free to roll. Q5. What are the assumptions that can be made in this problem? (A) Traction force is due to the rear wheels only (B) The wheels have negligible mass (C) There is no change in gravitational force (D) All of the above Q6. What is the acceleration of the lorry (m/s²) (→)? (A) 0.675 (B) 0.908 (C) 1.125 (D) 1.850 Q7. What is the traction force on the wheels at A? () (A) FA= 1850 N (B) FA=2250 N (C) FA=2850 N (D) FA=3150 N
Ex.8. A crate of mass 10.0 kg is pulled up a rough incline with an initial speed of 1.50 m/s. The pulling force is 10ON parallel to the incline, which makes an angle of 20.0° with the horizontal. The coefficient of kinetic friction is 0.400, and the crate is pulled 5.00m. (a) How much work is done by gravity? (b) How much energy is lost due to friction? (c) Hemuch work is don the change in wietic energy of the crate? (e) What is the speed of the crate after being pulled 5.00m? 5.00 m = 110° 70° 20° 20° F (a) (b)
Answer the following:
please answer this question with explination. many thanks !
Pile drivers are heavy, metal hammer used to drive posts into the ground when constructing a building. One such pile driver with a mass of 200 kg was lifted 3 meters above the ground then released, driving a beam 8 cm into the ground. What is the speed and exerted force of the pile driver if a 60-N frictional force is exerted by the guide rails on the pile driver.
7. A car whose brakes are locked skids to a stop 70 m from an initial velocity of 80 km/h. Find the coefficient of kinetic friction.
4) This Atwood's machine includes two blocks connected by a cable, going over a pulley without slipping. Block 1 (30.0 kg) is connected to a spring (70.0 N/m), and slides on a horizontal surface with a coefficient of kinetic friction of 0.0100. Block 2 is 50.0 kg, and hangs vertically from the cable. The pulley is a disk with a radius of 0.500 m, and its moment of inertia about the center of mass is 10. 0 kg-m“. a) Draw the three free body diagrams, and write out Newton's 2nd Law for each. b) Derive the equation of motion (inhomogeneous 2nd order ODE) for this system. c) Use u-substitution to rewrite this as a homogeneous 2nd order ODE. d) Assume the position x as a function of time t is of the form x(t) = A cos (wt + p) I disk for undamped natural frequency w, phase angle P, and amplitude A. The initial conditions are: x(0) v(0) = -3. 00 m/s. Solve for the position of the mass as a function of time (you need to solve for w, 4, and A). = 2. 00 m and Mz
5.31 You are lowering two boxes, one on top of the othe down the ramp shown in Fig. E5.31 by pulling on a rope parallel the surface of the ramp. Both boxes move together at a consta speed of 15.0 cm/s. The coefficient of kinetic friction between t ramp and the lower box is 0.444, and the coefficient of static fri tion between the two boxes is 0.800. (a) What force do you need exert to accomplish this? (b) What are the magnitude and directic of the friction force on the upper box? Figure E5.31 32.0 kg 48.0 kg 2.50 m -4.75 m
You push a 1.00 kg food tray through the cafeteria line with a constant 9.0 N force. The tray pushes a 0.50 kg milk carton. The tray and carton slide on a horizontal surface so greasy that friction can be ignored. Find the acceleration of the tray and carton and the horizontal force that the tray exerts on the carton.