Show the conplete solution for this problem Problem 5.12Find the hydraulic power and mechanical efficiency of a centrifugal pump, direct connectedto a 5hp electrical motor operating at full load, for the following conditions: fluid handled, oilof s.g. = 0.85, oil temperature, 70F, volume of oil = 300 gpm, and total head created by thepump, 25 psig.

Shaft power = 5 hp S.G of oil = 0.85 Density of oil = 1000 × 0.85 = 850 kg/m³ Oil temperature = 70F…

Problem 5.12 Find the hydraulic power and mechanical efficiency of a centrifugal pump, direct connecte to a 5hp electrical motor operating at full load, for the following conditions: fluid handled, of s.g. = 0.85, oil temperature, 70F, volume of oil = 300 gpm, and total head created by the pump, 25 psig.

Problem 5.12 Find the hydraulic power and mechanical efficiency of a centrifugal pump, direct connecte to a 5hp electrical motor operating at full load, for the following conditions: fluid handled, of s.g. = 0.85, oil temperature, 70F, volume of oil = 300 gpm, and total head created by the pump, 25 psig.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

2. A rotary pump directly connected to a 5-Hp electric motor operating at full load under following conditions: a. Fluid Handled : 40 0API Oil b. Temperature : 210C c. Specific Gravity: 0.85 d. Volume Flow Rate : 20 lit/sec e. Total Head : 175 kPa Determine : i. Hydraulic Horsepower ii. Mechanical Efficiency
S 3
Determine the maximum suction elevation in feet below pump centerline
Q Consider the following data relating toperformance of a centrifugal pump:speed 1200 rpm, flow rate 30 L/s, head 20 m, and power 5 kW. If the speed of the pump is increased to 1500 rpm, assuming the efficiency isunaltered, Find the new flow rate and head.
The impeller of a centrifugal pump having external and internal diameter 500mm and 250mm respectively, width at out let 50mm and running at 200rpm works against a head of 48m. The velocity of flow through the impeller is constant and equal to 3m/s the vanes are set back at an angle of 400 at outlet. Determine A.inlet vane angle B.workdone by the impeller on water per second c.manometric efficiency
Consider the following data relating toperformance of a centrifugal pump:speed 1200 rpm, flow rate 30 L/s, head 20 m, and power 5 kW. If the speed of the pump is increased to 1500 rpm, assuming the efficiency isunaltered, Find the new flow rate and head.
quick answer pls
A submersible pump of 80 percent efficiency is used in pumping water with flow rate,Q from a river to a pool at an elevation, h. The frictional losses is assumed with losscoefficient, K = 10. By the aid of a labelled diagram, derive an expression on thepower require to drive the pump.
An axial flow pump discharges water at the rate of 78 m³/min and runs at 550 rpm. The total head is 10 m. Assume blade velocity of 22 m/s, flow velocity of 4.5 m/s, hydraulic efficiency of 0.87, and overall pump efficiency of 0.83. Calculate Cr OP 3.1. The power delivered to the water, and power input The impeller hub diameter and tip diameter 3.2. 3.3. The inlet and outlet blade angles for the rotor 30 07:30 S
a pump operating at 1750 rpm delivering 600 gpm against total head of 200 tt. changes in the piping system have increase the total head of 450 tt. At what RPM should the pump be operated to achieve thus new head at the same efficiency?
The two-lobe rotary pump moves 0.145 gal of a coal slurry in each lobe volume Vlobe. Calculate the volume flow rate of the slurry (in gpm) for the case where n. = 220 rpm.
If a pump with a manometric head of 12 m is designed to deliver a flow rate of 7500 liters / minute. Since the rotation speed of the pump shaft is 1800 rpm, what is the dimensionless pump specific speed of this pump?