PROBLEM 5. The forces P, Q, and F act of the bracket shown. Determine the equivalent resultant force-couple with the force acting at point A. The magnitudes of the forces are P = 1000N, Q = 1200 N, and F = 700 N. 75 mm 45 SUMMARY OF ANSWERS 50 mm R 50 mm B 30 CR 60 100 mm F y 100 mm E(100 mm, 150 mm, -50 mm)

PROBLEM 5. The forces P, Q, and F act of the bracket shown. Determine the equivalent resultant force-couple with the force acting at point A. The magnitudes of the forces are P = 1000N, Q = 1200 N, and F = 700 N. 75 mm 45 SUMMARY OF ANSWERS 50 mm R 50 mm B 30 CR 60 100 mm F y 100 mm E(100 mm, 150 mm, -50 mm)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

А L B 425 mm C 1,000 mm V P A steel bar (1) and an Aluminum bar (2) are connected to a rigid angle ACD. Assuming: • Steel [E = 200 GPa] bar (1) is 6mm x 40mm x 600mm long. • Aluminum [E = 70 GPa] bar (2) is 10mm x 40mm x 600mm long. Poisson's ratio, v = 0.35 • A distance L of 500mm. a)Determine the force P (in kN) required to stretch the Aluminum bar by 1mm. Enter the force, P, into the d21 answer box (in kN, 3 sig digs). b) Determine the final width and thickness of the Aluminum bar. (1) Your Answer:
Determine the force in member EB of the roof truss shown in the figure below. Indicate whether the member is in tension or compression.
QL7
Homework H.W1: Determine the design moment strength for each of the following A) f = 25 MPa fy = 420 MPa %3D 70 mm 520 mm 540 mm S425 300 mm 2 m 2 m
A load of P = 2800 N acts on the machine part shown. The angle between the line of action of Pand the vertical y axis has a value of - 75°. The overall dimensions of the machine part are a= 125 mm, b - 55 mm, and c-75 mm. K B.
The figure as shown below is a rigid bar (ABCD) which was supported thru pin at B. Two bars was also connected, Bar CE and Bar DF with corresponding cross-sectional area and Modulus of Elasticity. If P is equivalent to SN kN, the diameter at pin B is Blank 1 mm. SN=78
Question #4: Two cylindrical rods, one of steel and the other of brass, are joined at C and restrained by rigid supports at A and E. For the loading shown and knowing that Es = 200 GPa and Eb = 105 GPa, determine (dsteeF 40 mm, dbrass = 30 mm) 1- The reactions at A and E. 2- The deflection at C. 180 B 120 * 60kN 100 100 40 RN D Steel Brass Dimensions in mm.
The bar composed of aluminum was sustained by the 14 mm2 cross-sectional area of the pin-connected rod CB. When the bar is vertically deflected at D, calculate the vertical deflection of the bar when distributed load is applied Given: E = 68.9 x 10^9 Pa
SHOW COMPLETE SOLUTIONS AND FB
* A For the RIGID beam shown, find the :deflection at point B 2m B 3m C 3m 50 kN ID +0.025 m O -0.025 m O Non of them O -0.125 m O +0.125 m O No deflection O
Given the image below what is the equivalent force-bouple at poitn A at tension of cord Cg when Tcg = 52.1N?
8) If the elongation of wire BC is 0.2 mm after the force P is applied, determine the magnitude of force P. The wire BC is A36 steel and has a diameter of 3 mm. 200 G Pa E A36 400 mm 300 mm B 200 mm-