Problem 5 (2Let rn] be a sequence such that X(w) is real and nonzero for all w. Let yn] = r[n-1] andz[n] = x{n-2]. Show that Y(w) and Z(w) cannot be real except at certain frequencies w thatyou have to specify.

The reason is prity simple and to explain we have to use the time shifting property and as we know…

Problem 5 [2 Let r[n] be a sequence such that X(w) is real and nonzero for all w. Let yn] = rn-1] and !! z[n] = r{n-2]. Show that Y(w) and Z(w) cannot be real except at certain frequencies w that you have to specify.

Problem 5 [2 Let r[n] be a sequence such that X(w) is real and nonzero for all w. Let yn] = rn-1] and !! z[n] = r{n-2]. Show that Y(w) and Z(w) cannot be real except at certain frequencies w that you have to specify.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

4.4-8 Weaver's method for SSB-SC modulation requires two steps. Consider a message signal m(t) whose frequency response is M(f)= 1 j2лf [u(f+500)u(f +50)]+ [uf-50) – uf- 500)] Note that this message has a 100 Hz gap near 0 Hz. j2лf (a) Design an upper sideband SSB-SC modulator using a first-stage carrier frequency f₁ = 600 Hz by providing the block diagram and the required bandpass filter. (b) What is the guardband to center frequency ratio required for the bandpass filter in (a)? (c) Design another upper sideband SSB-SC modulator using a first-stage SSB-SC signal such that the final carrier frequency fc = 150 kHz. (d) What is the guardband to center frequency ratio required for the bandpass filter in (c)? (e) If you generate an upper sideband SSB-SC modulator directly by using a single-stage =900 kHz, what would be the required modulator such that the final carrier frequency fe guardband to center frequency ratio for the bandpass filter?
The plot in the figure below shows the frequency content of a continuous signal. Determine the minimum sampling frequency, in Hertz, that can be used in order to ensure aliasing is avoided. (+-10% tolerance. Enter a numerical answer only) 30 25 20 Magnitude ✔ 10 5 0 0 0.2 Frequency Content of a Continuous Signal 0.4 0.6 1.2 0.8 1 Frequency (Hz) 1.4 1.6 1.8 2 #105
4. What do the Hartley's law tells us? A. Information capacity in a given channel is non-linear function of time and bandwidth B. Information capacity is linear function of time and bandwidth C. Information capacity is inversely proportional of the time and bandwidth D. All of the above
For the sequence x1) = {4, 6, 9, 10} Decimate it. Filter h(n)= {0.25; h() = (0.5, 0.25) by a factor of 2. using the
Asiacell O HW_RoC_... → Find the ROC of the signals (a) a(n)= 0.8"u(n)+1.3"u(n) (b) 2(n)= 0.8"u(n)-1.3 u(-n - 1) (c) a(n)= -0.8"u(-n-1)-1.3'u(-n- 1)
A discrete time signal x[n]= {4,4,0,2} is applied to a 4-bit microprocessor to compute the frequency domain sequence which is periodic and discrete in nature. Assume the microprocessor computes the frequency coefficients in a fast and efficient manner than the conventional method.
(a) Specify v1(0) and v2(0) for determining the equivalent circuit involving the capacitors for t≥0. : (b) At t0=0.2 s, determine the currennt i(t0=0.2 s): (c) At t0=0.2 s, determine υ1(t0) and υ2(t0):
Ql : prove 1 2(1–2) 3(1--2) !! dydxdz = 1 0.
Question 1 Determine the convolution y(n) of the input x(w) and the frequency response h(w). (Hint do not include any space and separate each value with a comma) x(w)= -2+ew 2012w h(w)=3-w2w-40w+2012 y(n) = ? -2,3,-5,9,-2.-6,4
Let xn] be a sequence such that X(w) is real and nonzero for all w. Let y[n] = xn-1 and z/n] = x[n-2]. Show that Y (w) and Z(w) cannot be real except at certain frequencies w that you have to specify.
Hello, please solve the question. Which are the filter applications? Where are the types of filters used with the method of work in brief?
In the figure on the left, the transfer function of the system (SIST) block is 1/s² and the input-output relationship of the controller (KONT) block is as follows. KONT SİST + А, ={_2A, e >0 e <0 Here A is a real number. Zero (r= 0) is given as a reference. a. Let A= 1 Draw and interpret the phase portrait. b. Let A = 2 Draw and interpret the phase portrait. c. Let A= -1 Draw and interpret a phase portrait.