Problem: 4 The following figure, the beam has a weight of 10 kN is hanged to wall at pin C and roof by a cable AB and CD. It is steel cable has a diameter of 2 cm and its modulus of elasticity is 20 GPa. a. Calculate tensional force at cable AB b. Calculate stress at cable AB c. Calculate elognation (size change) at cable AB (TAB=? in Newton) (GAB=? in MPa) (ALAB=? in mm) ROOF Cable D=2,5 cm E=20 GPa 5 m 6 m A 60° WALL W=10 kN

Problem: 4 The following figure, the beam has a weight of 10 kN is hanged to wall at pin C and roof by a cable AB and CD. It is steel cable has a diameter of 2 cm and its modulus of elasticity is 20 GPa. a. Calculate tensional force at cable AB b. Calculate stress at cable AB c. Calculate elognation (size change) at cable AB (TAB=? in Newton) (GAB=? in MPa) (ALAB=? in mm) ROOF Cable D=2,5 cm E=20 GPa 5 m 6 m A 60° WALL W=10 kN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Solve it new SOLUTIONs ok. Find All
a\ A steel tape has a cross-section of 13 mm*1 mm and weighs 0.122 kg per meter. When supported throughout its length and under a pull of 7 kg and a a temperature of 15° C, its length is 50 m. A line is measured with it and found to de 2560 m. In this measurement the tape was supported at the end only, the pull was 12 kg and the average temperature was 30° C. What is the true length of the line? Take the coefficient of expansion of tape as 12*10 per degree C, E= 2.11*10 kg\cm?. Assume the ends to be at the same level.
Determine the member force LK(kN) in the figure shown. "十2m十十 2 m 2 m 2 m 2 m 2 m- 2m 2 50 kN 50 kN 50 kN 50 kN M. 50 kN 50 kN 50 EN it 4 m V3 3 PLLLE B. D. 25 m-25 m - 3 m -3m 25 m4-2.5 m
i need the answer quickly
Make 2 free body diagrams
9. Find the moment of inertia of the object shown below. The shape is symmetrical from top to bottom, left to right, with the axis passing through the centre of each face.< Lx Lz X z Lx=0.5m Ly=5.0m Lz=0.5m Ly 500kg y ↑
Please solve, the correct answer is there. The correct solution and the correct FBD is all I need. Thank you
i need the answer quickly
)If V=i +2j+3K, V,=zi+zj +2K, V= 3i+3j +K, find the Volume?
Determine the horizontaldeflection of B.
In (Figure 1), F = {80i + 96j + 48k} lb. Figure 1 ft -2 ft 3 ft 45° B 1 of 1 Part A Determine the magnitude of the moment of F about point A. Express your answer in pound-feet to three significant figures. 15] ΑΣΦ11 MA = Submit Part B α, B, y = Submit Request Answer Provide Feedback Determine the coordinate direction angles of the moment of F about point A. Express your answers in degrees to three significant figures separated by commas. vec U/ ΨΕ ΑΣΦ ↓↑ vec Request Answer ? lb. ft ? Next >
The object W1 in the figure is at an angle of 45 to the horizontalIt is based on its frictionless surface at point B.Point A is articulated (fixed support) and ground frictionSince (μ = 0.3) body W2 is a surfaceWhat should be the weight of W1 that will cause it to start? W2= 38 [kN]sin45=cos45=0.7