PROBLEM 4 Replace the system of forces shown with a single force and then, determine the distance of the this force from O and its intersection with the X and Y axes. 200 N 600 N ASOON √60° 1450mm 1450 mm 300mm 200 W f 400mm

Q: Draw orthographic views of the figure with dimensions

A: The isometric view the three dimensional which is drawn in the two dimension.  The orthogonal view…

Q: III-3 BASIC STANDARDS IN TECHNICAL DRAWING III-3-1 Formats These are. on which are executed the…

A: To fill the blanks in the given question.

Q: 32. What is the area of an octagon inscribed in a circle having an area of 224 sq.m?

A:

Q: What is the importance of scaling the drawing to different paper size

A: Explanation:  Scaling in engineering drawings is very important aspect of any kind of drawing. To…

Q: ngineering Drawing Give the definition and uses of the following Alphabet of Lines. 1. Object or…

A: The definition of the various lines that are used while plotting a particular layout in an…

Q: What is the relationship between the drawing and specification/

A:

Q: When does the misuse of drawings occur?

A: # Usually As-built drawings are made by the contractor. These seem more like interpolations…

Q: List the four distinct kinds of drawings according to their projection methodologies.

A:

Q: What dimensioning rules apply to isometric drawings?

A: Use of isometric drawings - 1. It gives clear understanding of the drawn object. 2. In an isometric…

Q: Explain how the symbol modes of Live and Rectangle mode, Arc and Circle mode, Dimension and…

A: Introduction:- Geographic Information systems in the area of surveying involve the development of a…

Q: The ABC rod is supported from point B and is in equilibrium with a force F1 = 12KN applied from…

A: Given Data: The equilibrium force F1 is, F1=12 kN The shear strength at pin B is, τs=350 MPa The…

Q: derivation of the formulas used in every section

A: This question has been taken from fluid mechanics

Q: How are units converted using dimensional analysis?

A:

Q: Question : What is architectural drawing? Explain different views of a drawing.

A: An architectural drawing or architect's drawing is a technical drawing of a building (or building…

Q: why does the field of engineering need standardization in technical drawing?

A: Standardization in technical drawings mean ensuring and fixing certain parameters in drawings to…

Q: Given the following isometric drawing, draw the top view, front view, and right side view

A:

Q: 1. There are two approved ANSI systems of dimensioning on drawings when it comes to engineering…

A: The 2 types dimensioning methods are: 1. Aligned method 2. Unidirectional method.

Q: can you put an illustration?

A: Data Available: Shape of the tank = Cylindrical Diamter of the tank = 1.5 mHeight of the oriface =…

Q: What text style is used on technical drawings?

A: The text style is used on technical drawings is mentioned in the following step

Q: (a) Describe the purpose of detail design in your own words.

A: Detail design: Detail design involves the complte design procedure. The design procedure of every…

Q: Identify the several types of lines used in drawing and explain their uses

A: To list different types of lines used in engineering drawing

Q: What size will it be if 4" is at scale 2"=1"

A: Given tha scale  2"=1" Thus defines the sclae ratio  for a drawing is 2:1. Scale ratio = drawing…

Q: Each of the following parts was created with one feature. Name the Base feature for each part.…

A: Base feature : It is called as starting feature before creating an object. 2D geometry : It is 2…

Q: 50 10 Derive the third projection, taking into account the use of the rules for writing dimensions…

A: GIVEN: TO DETERMINE: TOP VIEW

Q: draw the front view, side view, and top view

A: Isometric view is given. We need to draw front view, side view and top view

Q: can you show detailed steps?

A:

Q: How are lines used in Construction Drawings and why are they important?

A: Explanation of lines importance and uses.

Q: A proportion determining the relationship of a representation to that which it represents. A)…

A:

Q: isometric plane

A: An isometric view is the 3D representation of a building ,room etc on a 2 dimensional surface. We…

Q: can you show the sides with dimensioning

A: To show the sides with dimensioning

Q: If all lines on a drawing are the same thickness, how can walls and partitions, for example,…

A: Engineering drawing shows the plans, cross sections  elevation etc of any structure.  The…

Q: What are the types of coordinate system? Illustrate with neat figure.

A: Generally two types of coordinate systems viz, Catesian Coordinate. Polar Coordinate.  Cartesian…

Q: For each condensed structural formula, write a line- angle formula.

A:

Q: Part 1 Answer briefly: 1. Give at least three (3) distinctions between paraline drawings and…

A:

Q: How are the following line types used on orthographic views of engineering drawing? Short break…

A: Solution:- The following line types used in engineering drawing is shown below, 1) Shorty break line…

Q: 5. Draw a diagonal scale 1:1000 to show 1.5 meter. Show a distance of 25.5 meters on it.

A: First to find length of scale

Unit Conversion

Standard units are also called SI units. SI units are used for measuring a physical quantity satisfying certain conditions. There are two types of units: fundamental units and derived units. Fundamental units are physical quantities that are independent, that is, they do not depend on other quantities like mass, length, or time. There are plenty of quantities in our lives which need to be measured and compared. Measuring is the comparison of a particular physical quantity with its reference value. A unit is a measure of a fixed physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.