Answered: Problem 4 Calculate the force P…

Name: Problem 4Calculate the force P necessary to hold the 4-m-wide gate in
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Problem 4Calculate the force P necessary to hold the 4-m-wide gate in the position shown in Fig. P2.57 if:(a) H=6m(b) H= 8 m(c) H = 10 mHinge5m/3 mHPWater

Engineering

Mechanical Engineering

Problem 4 Calculate the force P necessary to hold the 4-m- wide gate in the position shown in Fig. P2.57 if: (a) H=6m (b) H= 8 m (c) H = 10 m 5 m Hinge 3 m H P Water

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please give your own solution. Thank you
Weighted piston type accumulator is shown in the figure below. If area=340 cm², a lift of the ram =1190 mm. Calculate the capacity of the accumulator in terms of liters.
Air P Question 5. 1,2 m wide AB gate is articulated from point A shown in the figure. The heights of the fluids are 6 and 2 for h1 and h2, respectively. Water A hi Considering the measured pressure P = -15 kN/m?, find the magnitude of the force Oil h2 *(kN) that will affect point B, in which the в force provides the balance in AB gate (SGoil = 0,75). Figure 5
M1
A homogeneous rectangular gate AB 5.1 ft wide and 10 ft long. Friction in the hinge is negligible. Find force acted on surface AB? L = 7.17 ft 60 A water B hinge
A rectangular gate of width "a", length "b" and inclined at an angle "A", with water on one side is shown in the figure. Use a=9.5 ft, b=5ft, z=6.5ft and angle A=55 degrees. (a) Determine the location of the center of the gate from the water surface along the plane of the gate (in feet). (b) Determine the eccentricity (in feet). (c) Determine the location of the center of pressure from the water surface along the plane of the gate (in feet). (d) Determine the vertical distance (in feet) of the center of the gate from the water surface. (e) Determine the total resultant force (in lb) acting on the side of the gate.
Smwidth x Sm leng th The plate used to support the water as shown in Figure Q1 (c) is a S sn square. The value of h is 4.5 m. Ignore the atmospheric pressure, determine the tension of the горе, Т. (c) T Rope h 450 Figure QI (c)
Q³Gate AB in Fig. 3-5(a) is 4 ft wide and is hinged at A. Gage G reads -2.17 psi, and oil of specific gravity 0.750 is in the right-hand tank. What horizontal force must be applied at B for equilibrium of gate AB? )G Air | 4, Ay T -IWS 5.01' A A Water 18' 3.30' 4' Oil 15,000 lb 3370 lb 6' EB B F C (a) (b) Fig. 3-5
Question #4 A crane is used to lower weights into the sea (p = 1025 kg/m³) for an underwater construc- tion project (see figure below). You are required to calculate the tension in the rope of the crane due to a rectangular 0.4-m x 0.4-m x 3-m concrete block (p= 2300 kg/m³) when: 41. Rope Concrete block W Concrete block W Air Water (A) suspended in the air. (B) completely immersed in water. (C) Does the tension of the rope decreased in water? Why? How much reduction in percentage? [2 marks] (4 marks] (4 marks]
Problem: Use a unit length for the gate, determine the height h (m) in fluid 2 in the figure below if the weightless triangular hinged gate is in equilibrium in the position shown. Assume y₂ = 1.5 ₁ Triangular Gate 1m Fluid 1 45° Hinge Fluid 2
Q3: In Figure below, the gauge pressure, G reads (- 2.35) Psi and gate AB has a height of 6 ft and width of 3.5 ft was fixed in A. Find the required force F on the gate at B. Air T Water 18 Oil 6' S= 080 B
An underwater pipeline must be laid 40 meters deep. The density of sea water is 1 025 kg/m³. The pipe has a mass of 40 kg per meter and an outside diameter of 300 mm. The pipe must be anchored every 5 m to the bottom of the sea. (a) What will the vertical force be on each anchor if the 4.3 pipe is empty. (b) What external pressure must the pipe be able to withstand if it is not to be crushed. [1 592 N, 402,2 kPa]