determine the values of , φ, and φMnfor the sections shown. Problem 3.7 (Ans. ØM,379.1 ft-k)24 in.27 in.4 #9 bars$ 3 in.fy = 60,000 psif':= 4,000 psi-12 in.-

Answered: Problem 3.7 (Ans. ØM„ = 379.1 ft-k) 24…

Engineering

Civil Engineering

Problem 3.7 (Ans. ØM„ = 379.1 ft-k) 24 in. 27 in. 4 #9 bars 3 in. fy = 60,000 psi f:= 4,000 psi %3D -12 in.-

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the force in each member of the loaded truss. The force is positive if in tension, negative if in compression. AB= AC = A Answers: BC= 37 53 i i i B 219 kg N Z Z Z N N
Use the method of joints to determine the force in each member of the truss shown in the following problems. State whether each member is in tension or compression. The value of x =25
Rigid bar ABC is supported by two aluminum alloy (E = 10,000 ksi) rods as shown below. The horizontal distance between rods (1) and (2) is a = 120 in. Rod (1) has a length of L1 = 87 in. and a cross-sectional area of A1 = 0.65 in.2. Rod (2) has a length of L2 = 84 in. and a cross-sectional area of A2 = 1.15 in.2. Rigid bar ABC is to remain horizontal under a load of P = 25 kips. Determine the distance x (in inches rounded to the nearest tenths) from joint A to the location of load P so that bar ABC remains horizontal.
From the figure shown, a truss is subjected to loads PI = 15 kN, P2 = 15 kN and P3 = 25 kN at joint C, D and E respectively. Use SI = 3 m; S2 = 4 m P₁ Properties of diagonal members (2L75 x 75 x 6): Ag = 1858 mm2 Fy = 248 MPa rx = 22.9 mm ry = 33.2 mm G a) What is the axial force in kN, in member DI? b) What is the allowable stress in MPa, in member DI? c) Calculate the allowable load in kN, in member DI. H 6 @ Si I P₁ E B S, CIVIL ENGINEERING- STEEL DESIGN ...
Problem 2: A beam is made of four rectangular boards nailed together as shown. Note that the nails at C are aligned horizontally, while the nails at D are aligned vertically. Each nail can support a shear force Fs = 100 lb, and the entire beam cross section is subjected to an internal shear force V = 710 lb. (a) Determine the maximum spacing, s, for the horizontal nails. (b) Determine the maximum spacing, s', for the vertical nails. in. 10 in. A 10 in. BL 1 in. KE 1.5 in. 1 in. 2 in.
COMPUTE FOR THE CENTROID: INNER RADII= 1 ; OUTER RADII= 2
The beam is made from four boards nailed together as shown below. If the nails can each support a shear force of 500 N, determine their required spacing s' and s if the beam is subjected to a shear of V = 3.5 KN. 25 mm 250 mm 250 aut BE 40 mm 25 mm 25 mm 50 mx
Determine the force in each member of the loaded truss. The force is positive if in tension, negative if in compression. AB= 31° 59 Answers: BC= 10 B 218 kg i 1870 AC = i -1870 i -1120 N Z Z Z N N
View Policies Current Attempt in Progress Determine the force in each member of the loaded truss. The force is positive if in tension, negative if in compression. Answers: AB= AC = i i IM BC= i 69° 14° 45° W B W W W
Part A In (Figure 1), r = 30 mm. Locate the centroid a of the metal cross section. Neglect the thickness of the material and slight bends at the corners Express your answer to three significant figures and include the appropriate units. T = 0 mm Submit Previous Answers Correct Figure < 1 of 1 Part B Locate the centroid ī of the metal cross section. Neglect the thickness of the material and slight bends at the corners Express your answer to three significant figures and include the appropriate units. HẢ ? 150 mm = Value Units Submit Previous Answers Request Answer 50 mm 100 mm 100 mm 50 mm
Can you help me with my homeowrk?
1.