Problem 3 The buck-boost converter shown below has the following parameters: Vin = 12 VDC, D = 0.58, L = 9.8 µH, C = 19.5 µF, R = 102, and f, = 200 kHz. Find (a) the output voltage, V. (b) the maximum inductor current, Imax (c) the minimum inductor current, ILmin and (d) the output AV voltage ripple, Assume ideal components. elell iD

Problem 3 The buck-boost converter shown below has the following parameters: Vin = 12 VDC, D = 0.58, L = 9.8 µH, C = 19.5 µF, R = 102, and f, = 200 kHz. Find (a) the output voltage, V. (b) the maximum inductor current, Imax (c) the minimum inductor current, ILmin and (d) the output AV voltage ripple, Assume ideal components. elell iD

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

i need the answer quickly
35 - Which of the following is a two-ended trigger element that passes current in two directions?A) DiodeB) TransistorC) ZenerD) OpampE) Diac
A stabilization circuit has a stability factor of 0.04 and an internal resistance of 5 2. The unstabilized voltage can vary between 75 and 100 V, and the load current can vary from 40 to 80 mA. Determine the maximum and minimum values for the stabilized load voltage.
For the buck-boost converter, determine the duty cycle, the switching frequency, and the inductor current ripple. The output voltage ripple is about 1%. vs 10 V, mH, C 0.5 micro.F, Vout=-20 V, R-IO Q
In the given circuit, D1 is Silicon diode and D2 is a zener diode with breakdown voltage of 6.8V. Assuming RC time constant of circuit >> T. Find the Maximum and Minimum value of the output waveform.
a2/a.Design Circint as the following pescripton: A- the positive Cyycle of the vout signal is 3.2 and Negate cycle is 4-3 (Note: we must used preetical Diodes and vin is tov) 1B- the positive cycleg of vout is 5-3 and Negative cycle is (5. 4) [note: consider tovavd we must used Cupaetor with praetical Drade) Vin اضف ملف
b) A Buck-Boost converter has an output of 24 V from a 5 V input with diode ripple current of 2.4 A and switching frequency of 100 kHz. Find the duty cycle and the inductance of the converter.
Op amp and diodes are ideal. Derive Vout and sketch the transfer curve of Vin vs Vout. Please show complete solution.
For Steady-State Operation o f Boost DC-DC Converter What is the duty ratio (D) How can it effects on the converter output (Vo)
Sub:power electric
Find Idc, Vdc and the capacitance that will force the Vr(pp) to 3mV. Draw the output waveform across the capacitor. Fin=60Hz.
(Boost de-dc converter with continuous inductor current. Evaluation of inductor and capacitor values) EX3: The boost converter shown bellow has the following specifications: Vin = de input voltage = 12 V, de output voltage = 30 V, output voltage peak-to-peak ripple = 1% Inductor current peak-to-peak ripple 10%, f;= switching frequency = 25 kHz and R = load resistance = 50 N Assuming that the converter is ideal, calculate: a) The duty cycle. b) The average input current. c) The minimum required inductance that ensures continuous inductor current. d) The required inductance so that peak-to-peak current ripple = 10%. e) The minimum and maximum values of the input current. f) The value of the output capacitor so that the output voltage ripple = 1%. g) Verify the theoretical results with the respective simulation ones. Boost inductor Output filter capacitor D VL 1R Vin S R Vo