PROBLEM 3: A reinforced concrete beam has a width of 250mm and an effective depth of 500mm. The compressive strength of concrete is 28MPa and the yield strength of the steel reinforcement is 414MPa. 1. Compute the maximum number of 25mm diameter bars that can be used for the beam? 2. Using the maximum number of 25mm diameter bars, compute the nominal moment capacity of the beam. 3. Compute the total depth for the given beam.

PROBLEM 3: A reinforced concrete beam has a width of 250mm and an effective depth of 500mm. The compressive strength of concrete is 28MPa and the yield strength of the steel reinforcement is 414MPa. 1. Compute the maximum number of 25mm diameter bars that can be used for the beam? 2. Using the maximum number of 25mm diameter bars, compute the nominal moment capacity of the beam. 3. Compute the total depth for the given beam.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A cast iron tube 3m long is completely filled with concrete and used as a vertical strut. if the external diameter of the tube is 450mm and the wall is 35mm thick, determine the maximum compressive load the composite strut can support if the stress in the concrete is not exceed 2N/mm2. By how much should the strut shorten under this load. For cat iron EA= 100GN/m? and for concrete Eb = 10GN/m?. %3D
In all Questions use the Working Stress Method and the flowing material 25 MPa and f, = 420 MPa. properties f = If the stress in the top fiber of the concrete is f = 12.5MPa and in the steel is 400 MPa. Ec 25000 MPa, Es 200000 MPa. Determine the following: 1-Maximum strain in concrete 2- Maximum strain in steel and 3- Flexural strength of the section (the moment M) P 500 mm 300 mm
Assume concrete accepts no tension. Compute the bending stress in the extreme fiber of the beam of figure for bending moment 1.25ton.m A = 10cm? E, = 2*10 kg /cm? E. = 2*10°kg /cm f' =150kg / cm? F, = 4000kg / cm? 20 cm 25 cm 20 cm
Refer to the figure below. The square steel tube carries 130 kN of axial compressive force. Compute the compressive stress in the tube and the bearing stress between each contacting surface. Consider the weight of the concrete pier to be 2000 N. 100 mm 100 mm 4 mm Standard strutural steel tube-100x 100x 4 150 mmx 150 mm plate 300 mm x 300 mm Concrete pier 600 mm 600 mm Gravel
Problem #1. The base of a rectangular reinforced concrete beam is 300mm and the effective depth is 550mm. Concrete compressive strength on the 28" day is 24MPA and steel yield strength is 415MP.. Determine : a. The depth of compression block (in mm, 2 decimal places), the strain in the tension steel (5 decimal places) and ultimate moment capacity (in KN.m, nearest tenth) of the beam if it is reinforced with 4-32mm diameter bars. b. The depth of compression block, the strain in the tension steel and ultimate moment capacity of the beam if it is reinforced with 4-20mm diameter bars.
The concrete post in the figure is reinforced axially with four symmetrically placed steel bars, each of cross-sectional area 900 mm?. Compute the stress in each material when the 1000-kN axial load is applied. The moduli of elasticity are 200 GPa for steel and 14 GPa for concrete. Bearing | 1000 kN plate Steel Concrete 300 mm 300 mm Section a-a The stress in concrete = MPa (use up to 4 significant figures). The stress in steel = MPa (use up to 4 significant figures).
A square hollow steel structure with a wall thickness of t1 = 10 mm is pin linked to two gusset plates with a thickness of t2 = 12 mm, which are welded to a base plate with a thickness of 12 mm and secured to a concrete base with 4-16 mm diameter anchor bolts. The pin has a diameter of 16 mm. P = 48 kN compressive load, 30 deg. P= 48 kN Stnt gusset plate fy=12 mm 0=30 10 m 12 mm 16 mm ø anchor bolt 4-16 mm p 1. Determine the bearing stress in MPa between the struct and the pin. 2. Calculate the pin's shear stress in MPa. 3. Determine the anchor's shear stress in MPa.
A reinforced concrete beam is shown in the figure below. 0.75-in, diameter rods Wo 20 in. 2.5 in. 8 ft- 8 ft 10 in. Part A Determine the maximum uniform distributed load wn that can be supported by the reinforced concrete beam if the allowable tensile stress for the steel is (Ost )allow = 30 ksi and the allowable compressive stress for the concrete is (oconc )allow = 3 ksi . Assume the concrete cannot support a tensile stress. Take Est = 29(10) ksi , Econe = 3.6(103) ksi Express your answer to three significant figures.
Problem The following are the dimensions of a concrete T-beam section Width of flange, bf = 600 mm Thickness of flange, tf = 80 mm Width of web, bw = 300 mm Effective depth, d = 500 mm The beam is reinforced with 3-32 mm diameter bars in tension and is carrying a moment of 100 kN.m. Find the total compressive force in the concrete. Use n = 9.
A wood beam is strengthened using two steel plates as shown in the figure below. V 6 mm 150 mm 6 mm |B 100 mm i The beam has simple supports and an overhang and is subjected to a point load and a uniform load as shown in the figure below. 13 KN q= 5.0 kN/m с 3 m Calculate the maximum tensile and compressive stresses of the beam. Assume that E = 11 GPa and E = 200 GPa. (Enter your answers in MPa. Use the deformation sign convention.) maximum tensile stress in wood MPa maximum tensile stress in steel MPa MPa maximum compressive stress in wood maximum compressive stress in steel MPa Need Help? Read It B 000 +1m-
For the given section below, Compute the maximum stress of concrete and steel. All dimensions are in "mm". Use M=150KN-m and n=10. The answers are MPa and MPa 500 mm 100 mm 100 mm 400 mm 6-32 mm Ø 100 mm 100 mm, 100mn|,100 mal 100 mml100 ma,
A reinforced concrete beam experiences a load as shown. It has a base of 350 mm, and an effective depth of 600 mm, with 4 – 25 mm diameter rebars. The concrete has a compressive strength of 27.6 MPa, Determine the maximum distributed load that the beam can carry. Assume that the allowable stress in steel is 167 MPa (instead of 160 MPa). w 1.5 m 10 kN 1.5 m 5 m