Problem 3 A load of 20 kg is supported as shown in Fig. 1.12. Assuming the pulley to be ideel, determine the length of CD required to realize the equilibrium configuration shown. Also, determine the tension in the cable CD. [ FcD = 150.2 KN, CD = 1568 mm] %3! %3D

Problem 3 A load of 20 kg is supported as shown in Fig. 1.12. Assuming the pulley to be ideel, determine the length of CD required to realize the equilibrium configuration shown. Also, determine the tension in the cable CD. [ FcD = 150.2 KN, CD = 1568 mm] %3! %3D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Part C Rope BCA passes through a pulley at point C and supports a crate at point A. Rope segment CD supports the pulley and is attached to an eye anchor embedded in a wall. Rope segment BC creates an angle of d-68.0 with the floor and rope segment CD creates an angle with the horizontal. If both ropes BCA and CD can support a maximum tensile force To 140 lb, what is the maximum weight Was of the crate that the system can support? What is the angle @ required for equilibrium? Express your answers numerically in pounds and degrees to three significant figures separated by a comma. ▸ View Available Hint(s) VG ΑΣΦ. Η νοο ?
Three pulleys are joined by solid steel shafts AB and BC. If G = 200 GPa, determine the unit shearing stress in shafts BC. In MPa A 25 mm ara B 450 N-m 1.2 m 1300N-m 38 mm dia 1.80 m 900 N-m
TABLE 1.2 Minimum Densities for Design Loads from Materials Aluminum Concrete, cinder Concrete, stone Clay, dry Clay, damp Sand and gravel, dry loose Sand and gravel, wet Masonry, lightweight concrete Masonry, normal weight units Steel, cold-drawn Wood, Douglas Fir Wood, Southern Pine Wood, spruce AN/w 27 120 22.6 123 15.7 18.9 165 21.2 5.7 723 5.3 5.8 45 TABLE 1.3 Minimum Design Dead Loads From Paris and Walls Wood 1x plated Woodplatered Woodst 51x32mm, platered Cindere per Lightweight complaine Ceilings Aucuntic Shond Spendedahand Angle 5.54 9.57 2017 005 8:24 0.41 904 TABLE 1.4 Minimum Live Loade Oorspany or Use Amely Fixed seats and at Garage (can only) Officeday Lebbin Love Load 4.79 192 4.79 VEST S Occupancy or Use Dwelings (one-and two-mily) Hotels and many bo Private and don Campos Fint Coor comidon Comidon abfint floor Live Lead KN/² 190 4.39 3.33
3. The center post B of the assembly has an original length of 124.8 mm whereas posts A and C have a length of 125 mm. If the caps on the top and bottom can be considered rigid, determine the average normal stress in each post. The posts are made of aluminum and have a cross sectional area of 400 mm². Ea=70 GPa. Use the Force Method 100 mm -100 mm 800 kN/m 125 mm 800 kN/m
Using the Portal method of analysis, determine the vertical reactions at the support caused by the horizontal loading shown. 10kN 3m 9kN 3m 8kN 3m 7kN 3m 4m 3m 3m uTT
Problem 1. Determine the axial forces, shears, and bending moments at points A and B of the structures shown 150 kN 100 kN-m 25 kN/m antom I A B 4 m- 4 m 4 m- 2m 2m (b)
Find the stresses in members BC, BD, and CF for the truss shown in the figure. Indicate the tension or compression. The cross section nal area of each member 1600 mm². 3 m 84.853 kN (T) 3 m C 60 kN (C) A 4 m DE 135 kN (T) E 60 kN 90 kN 4 m F 45 kN (T)
(iv) Determine the force in member BC of the truss shown below. Is the member BC in tension or compression? Во 12 m a) 30 N in tension b) 54.3 N in tension c) 30 N in compression d) 54.3 N in compression 94.5 N 3.75 m 9 m
3. The center post B of the assembly has an original length of 124.8 mm whereas posts A and C have a length of 125 mm. If the caps on the top and bottom can be considered rigid, determine the average normal stress in each post. The posts are made of aluminum and have a cross sectional area of 400 mm². Ea=70 GPa. Use the Force Method 100 mm -100 mm 800 kN/m 125 mm 800 kN/m
The degree of static indeterminacy of a rigid jointed frame PQR supported as shown in figure is Cable R EI 90° El
3. Determine the required diameter of the pins at A and B to the nearest 1mm if the allowable shear stress for the material is T= 300 MPa. Pin A is subjected to doble shear, whereas pin B is subjected to single shear. A 1.5 m B 1.5 m C D 30 kN 2.25m
- Determine the force in member GH and state if the member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. FGH = Submit Part B. FBC= μA Value Part C Request Answer Determine the force in member BC and state if the member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. HA Value Submit Request Answer 3 μA Units FBG = Value → Units ? Determine the force in member BG and state if the member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. Units ? ?