Problem #20) Given the following circuit, determine the current Ipc that will in the circuit (as shown).wwwIDC 1000236VVDC20VwwwR₁ = 120Problem # 21) Determine the source current Ipc and the resistor voltage V4 as shown in the following circuitusing the Reduce and Return Method if the source voltage is VDc = 72 volts.R₂=402R₁ = 152IDC =R₁=4592.0.16IDC =.V₁ =(A)2 (A)(V)36

Problem # 20) Given the following circuit, determine the current Ipc that will in the circuit (as shown). IDC 100Ω VDC 36V 20V IDC = _ (A) Problem #21) Determine the source current Inc and the resistor voltage V4 as shown in the following circuit using the Reduce and Return Method if the source voltage is VDC = 72 volts. IDC www R₁ = 1202 R₂=402 www R₁ =1552 R₁=4502 0.16 IDC = V₁ = 3 2 2 (A) 36 (V)

Problem # 20) Given the following circuit, determine the current Ipc that will in the circuit (as shown). IDC 100Ω VDC 36V 20V IDC = _ (A) Problem #21) Determine the source current Inc and the resistor voltage V4 as shown in the following circuit using the Reduce and Return Method if the source voltage is VDC = 72 volts. IDC www R₁ = 1202 R₂=402 www R₁ =1552 R₁=4502 0.16 IDC = V₁ = 3 2 2 (A) 36 (V)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

3) Resistor is used as load in the circuit below. T1 and T4 thyristor is triggered at 30 degrees, T2 and T3 thyristor is triggered at 210 degrees. The effective voltage of the AC voltage applied to the circuit is 120 V. a) Draw the graph of the voltage on the load resistor.b) Neglect the voltage drop across the thyristors and find the average value of the load voltage.
Please answer it with clean and step by step solution. This subject is Electronics. Thank you and keep safe.
Find: a. Branch currentsb. Total current drawn by the circuitc. Total power drawn by the circuitd. Total power factor of the circuit Please show complete solution and draw the circuit diagram. Please round off answers up to the 3rd decimal places. Thank you!
I dont understand phase shift and lags?
Consider the circuit shown in Figure 1. V1 is a 7.2 kHz sine wave with an amplitude of 4 V.Figure 1: RC Circuit Schematic1. Determine the total impedance (Z) of the circuit.2. Using V1 as a zero-phase reference, calculate the values of the following:a) Amplitude and phase of current (I)b) Amplitude and phase of voltage across R1 (VR1)c) Amplitude and phase of voltage across C1 (VC1
Given the circuit shown, answer the following questions I 40 8n I3 Vs = 24/60° v E V2 -j4 n 12 one of the following statements is correct: Choose... 12 in Ampere equals to: Choose... the equivalent impedance in Ohm of the circuit is Choose... V2 in Volts equals to: Choose...
5
The three-phase phase voltages in the 3- phase thyristor rectifier circuit in the figure are as follows Ts T: A Ts a Van = V m sin (314t + 0°) V bn = Vm sin (314t – 120°) Ven = Vm sin (314t – 240°) Van Vea A T: A T: taking into account the network phase- to-phase voltage waveforms given below VAC VBC VCA VCB AB BA св Vm -Vm O 15 30 45 60 75 90 105 120 135 150 165 180 195 210 225 240 255 270 285 300 315 330 345 360 a) Write the Natural Trigger Angles for Thyristors in the rectifier circuit in the spaces below with values between 0-360 degrees (example: 30, 330 ) Response rating for T1? Response rating for T2 ? Response rating for T3 ? Response rating for T4 ? Response rating for T5 ? Response rating for T6 ? b) In cases where a=75° for the thyristors in the above rectifier circuit, specify the Switches in Conduct for the following ranges in the rectifier output voltage. In the range of 45° to 90°.? keys are in transmission. Between 165° and 195° .? keys are in transmission. In the range…
Q2) Non – sinusoidal voltage applied on 102 resistance with consumed power 521.25 watts and the current is i(t) =10sinwt+I3 sin3wt+0.5 sin5wt Amp. Find the I3 and the voltage effective value.
For the circuit given in Figure 1, a) Find the Thevenin equivalent circuit with respect to terminals a-b b) When a 5000 resistor is connected to terminal a-b, find the voltage on the resistor wwwwwwmm c) It will be connected to a-b terminals and its voltage on 5000 load will be 132 kV rms. What should be the capacitive reactance value that will increase it? wwwwwwwww d) What happens to the short-circuit current when the a-b terminals are short-circuited? 2+1202 000 m da 127/6 kV rms ob 1.5 +/902 000 w 12725 kV ms
Q1: Design the circuit shown below to maintain VL=12V for load variation current from 0 to 200 mA then find Rs and maximum power for the zener. RS 16 Vo W Vz RL Your answer Q2: Show and analysis the clamper circuit that give vo wave form in a and b Clamper Vo
Q2. For the circuit shown below, sketch the current waveforms iş and io and determine the Average and RMS for both currents. a = 50° TI 50 2 Vs = 300 sin 100zt ( cot T2 in cot