Problem 2.55 (Ans. 766 kN•m) 800 mm 80 mm fy= 420 MPa f = 28 MPa 300 mm 560 mm 6 #32 100 mm 80 mm 350 mm

Q: Which of the following most nearly gives the internal degree of indeterminacy? 102 34 28 84 Next ▸ ◄…

A: Is question is from structural analysis in this question a frame given and we are asked to find out…

Q: Determine the coordinates of the centroid of the shaded area. y 15 E 25 30 15 40 50 I 30 90…

A:

Q: Show the dimensions of the object on its orthographic views.

A: The orthographic views of the object using the third angle projection are as shown along with their…

Q: 4m 2m 2 m 4m 2 m

A: Find centroid of given section

Q: Provide the sectional front view, looking at the direction X, draw the top view, and left-side view…

A:

Q: Q3) In the following section: a) Calculate the coordinates of the center of gravity 8 6.

A:

Q: y = kx³ I 30 mm Fig. P5.15 30 mm 150 mm X

A: Locate the centroid of the plane area shown.

Q: 1.16. Name the two commonly used systems of measurement. How are they related?

A: Brief concept introduction- Systems of measurement are required to express various physical…

Q: y 74 mm 36 mm - 36 -+ 36 mm mm Answer: y = i mm

A:

Q: A cube of edge 24mm is resting on the top of a frustum of cone of base diameter 60mm and top…

A: In the engineering graphics we can draw both the 2 dimensional projection and 3 dimensional…

Q: Show me this drawing Step by step how to draw it. thank you 25 1209 105° 30 Ø16 60° 40 60 70 it's…

A: To Determine Steps to be followed to draw the given drawing in CADD software.

Q: A clockwise couple M = 4.5 N m is resisted by the shaft of the electric motor. (Figure 1) Part A…

A: Given: The moment M is 4.5 N.m. Consider the figure,

Q: y 200 mm 300 mm → 125 mm 125 mm 60 mm 150 mm

A:

Q: Line #4 AB BC CD DE EA Dist. 32.41 44.60 45.90 22.80 14.50 BEARINGS forward S 62-25 E N 41-34 E N…

A:

Q: 3. A 12m beam simply supported at 1.3m from both ends carries a uniformly distributed load of 18KN/m…

A:

Q: Determine the coordinates of the centroid of the shaded area. 20 60 Answers: x= y= i i 35 20 40 125…

A: Given values: Consider the area given.  Divide the area into sub parts to locate centroid.

Q: Determine the coordinates of the centroid of the shaded area. | 20 40 50 20 50 60 40 140 Dimensions…

A: Determine coordinates centroid of the shaded area

Q: find the x bar at the location of centroid along y axis

A: To find x bar

Q: -400 300 200, 200 Dimensions in mm 400 300 X

A: The given figure can be considered as (a) Rectangle, (b) Semi-circle and (c) Triangle

Q: CEM I 52.5 N: Define what each word/number/letter is?CEM I: .... 52.5: .... N: .... ....

A: Brief concept- This CEM I 52.5 N is related to the cement and its types and classification. The…

Q: Let F₁ = [F1] N. i) Express F₁ as a Cartesian vector. F₁ X 3 5 4 30° 45° F₂= = 450 N - y

A: To represent F1 as a Cartesian vector. F1 = 647 N

Q: Determine the coordinates of the centroid of the shaded area. y 15 E 30 35 15 40 50 I 30 - x 100…

A:

Q: What vector is generated by the following statement?x=linspace(0, 1, 5) 0, 0.2, 0.4, 0.6, 0.8 O 0,…

A: Asked: To choose the correct output for the given MATLAB command.   Given: x=linspace(0,1,5)   Here,…

Q: Find the x-coordinate of the centroid in 120 mm mm. - 60 mm - 40 mm 80 mm 60 mm

A:

Q: Find the centroid 20 30 25

A: A1=12×20×25=250 square unitA2=30×25=750 square unitA3=π×1522=353.43 square unit

Q: Locate the centroid for the following areas :

A: Figure is as shown

Q: B 75 mm 250 mm 40° A

A: Draw FBD: let us suppose AB as part 1 and BC as part 2: l1=250…

Q: An L-shaped bracket is fastened to the wall (x-z plane) at points A and B and extends out parallel…

A: Given: A L shaped bracket with 200 N force acting at C  Required: Moment at point A in vector form…

Q: Which of the following most nearly gives the external degree of indeterminacy? 8 28 24 21

A:

Q: 70 22 D 42 36 33

A: The three views are shown in the next step

Q: Determine the coordinates of the centroid of the shaded area. 10 40 y X = K15 Answers: y= i 10 |10|…

A:

Q: For the truss shown, determine the stress in members DC and DG. The area of each member is 800 sq.…

A: Given data: Area of each member is 800 mm2.