Problem 2.21 An inverted U-tube manometer is connected to two horizontal pipes A and B through which water is flowing. The vertical distance between the axes of these pipes is 30 cm. When an oil of specific gravity 0.8 is used as a gauge fluid, the vertical heights of water columns in the two imbs of the inverted manometer (when measured from the respective centre lines of the pipes) are nd to be same and equal to 35 cm. Determine the difference of pressure between the pipes.

Problem 2.21 An inverted U-tube manometer is connected to two horizontal pipes A and B through which water is flowing. The vertical distance between the axes of these pipes is 30 cm. When an oil of specific gravity 0.8 is used as a gauge fluid, the vertical heights of water columns in the two imbs of the inverted manometer (when measured from the respective centre lines of the pipes) are nd to be same and equal to 35 cm. Determine the difference of pressure between the pipes.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In a lathe machine the cutting tool has a diameter of 1.6 cm is subjected to a cutting force of 250 N. Compute and identify the nearest value of work done per revolution of the spindle. a. 12.57 Nm. b. 36.88 Nm. c. 23.98 Nm. d. 58 Nm.
21.37 You will note that the values of a and b in Eq. (21.24) are higher for high-speed steels than for carbides. Why is this so?
A cylindrical rod is machined using turning processes. It is given that the cutting speed is 120min ¹, and feed per tooth is 0.0025 m/min. The outer diameter is 35mm, the length of the rod is 130m and the inner diameter is 22mm. The number of teeth is 6. Find Rotational speed, Feed rate, Machining time, and Depth of cut.
Please don't provide handwritten solution...
The spur gearing arrangement made of two parallel shafts,whose pitch circle diameters of driven and driver gears are 84cm and 35cm respectively. If driven shaft runs with 10 r.p.s,determine the following; 1. Center distance between the two shafts in mm. 2. Speed of driver shaft in rpm 3. Velocity ratio 4. Number of teeth's on driver and driven shaft for the given module 6mm
A steel shaft of 75 mm diameter and 250 mm long turned on a lathe. Speed of spindle = 2 m/s, feed = 0.25 mm/rev. Find time required for 50 jobs by assuming 2 minutes for handling of each job.
Power is supplied at the rate of 0.40 hp for 2 min in drilling a hole in a 1.0 lb brass block. (a) How much heat is generated? (b) What is the rise in temperature of the brass if 75% of the heat generated warms the brass? What happens to the other 25%? (don't change the hp, lb)
3
A helical gear of 10 inches pitch diameter has a helix angle of 25 degree, and there are 35 teeth. The gear transmits 40 hp and rotates at 450 rpm with a normal pressure angle of 20 degrees. What is the value of the circular pitch in mm per tooth?
To facilitate the milling (roughing) work of a cast steel material using a 1.5 inch diameter cutter choose between the two available stock. Find the speed of the cutter in rpm. – high speed steel cutter with a cutting speed of 50 fpm or – carbide tipped cutter with a cutting speed of 200 fpm.
For the operation of straight turning in a lathe machine, the diameter of the workpiece is 80 mm, the length is 0.12 m, the cutting speed is 80 m / min, the feed is 0.5 mm / rev and the depth of cut is 0.002 m . Find the material removing rate and the time of machining.
Angle of twist is . . to shear modulus. a. not related with O b. directly proportional c. inverse proportional d. exponentially proportional