how to solve the question attached mmmmmAmžinęčNE50%NămânememProblem 2.2 - Find a) the position vector from point A to B. b) theunit vector UAB in the same direction, c) the direction cosines of rnĢığım8m----měgum30EmCumérčugā…………………………dmund

Answered: Image /qna-images/answer/793f27fb-6ad8-47f7-87a1-28a4afe035f8.jpg

Answered: Problem 2.2 - Find a) the position…

Problem 2.2 - Find a) the position vector r from point A to B. b) the unit vector u in the same direction, c) the direction cosines of ra immuuğuna 50° 8m En 30% -2m LE E

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A Brinell test is performed on a steel using a 1.2 in. diameter indenter with a load of 71825 Ibs. A 0.75 in. Determine in indentation was measured on the surface of the steel. Determine: a) HBN (psi); b) tensile strength (psi) a) HBN = psi b) Tensile strength = psi
Please provide more details for question b and c. thank you
Could you please spreate each question alone because there are two questions
how did it become 0.1077?
Please answer 3, 4, 5, 6, 8, 9, 10, 12 1 is 0, 2 is 0, 7 is point A, 11 is 2. I included a picture of someone who solved but they were mostly incorrect. Please do not answer if the solution set I provided with the incorrect answers was you. I appreciate the attempt, but the solutions for 3, 4, 5, 6, 8, 9, 10, 12 were marked wrong, so unless you have different answers, please do not submit the same incorrect solution set. The wheel is attached to the spring. The mass of the wheel is m=20 kg. The radius of the wheel is 0.6m. The radius of gyration kG=0.4 m. The spring’s unstretched length is L0=1.0 m. The stiffness coefficient of the spring is k=2.0 N/m. The wheel is released from rest at the state 1 when the angle between the spring and the vertical direction is θ=30°. The wheel rolls without slipping and passes the position at the state 2 when the angle is θ=0°. The spring’s length at the state 2 is L2=4 m. (1) If the mass center G is set as the origin (datum), the gravitational…
Hi, Could you please help with this question, if you need to take more credits then please feel free. showing working out if possible too please, Thank you
Please give a steps by steps explanation of each question answer please. Thanks you so much
Q1/A) Answer only Seven_of the following multiple choice: 1- Brass can be classified in one of the following materials categories: a- Ferrous material. b- Non-ferrous material. c- Composite material. d- Non-metallic. 2- The crystal lattice has a --- a- One dimensional. b- Two dimensional. c- Three dimensional d- Four dimensional. 3- The coordination number for FCC structure is: arrangement а- 2 b- 4 с-8 d- 12 properties c-Mechanical 4- Material density classified as a- Physical. 5- The ability of materials to resist impact is named a- Ductility. 6- One of the following hardness tests are not classified as a macro hardness test: b- Chemical. d- Thermal. b- Toughness. c- Strength. d- Elasticity. a-Brinell hardness. b-Vickers hardness. c- Knoop diamond. d-Rockwell hardness. 7- Due to Allotropy phenomenon, Iron in range of temperature varried between 769 and 910 C° has one of the following names and crystal strutures: a- Gamma (BCC). 8- One of the following hardening processes not need to…
Question 2 You are a biomedical engineer working for a small orthopaedic firm that fabricates rectangular shaped fracture fixation plates from titanium alloy (model = "Ti Fix-It") materials. A recent clinical report documents some problems with the plates implanted into fractured limbs. Specifically, some plates have become permanently bent while patients are in rehab and doing partial weight bearing activities. Your boss asks you to review the technical report that was generated by the previous test engineer (whose job you now have!) and used to verify the design. The brief report states the following... "Ti Fix-It plates were manufactured from Ti-6Al-4V (grade 5) and machined into solid 150 mm long beams with a 4 mm thick and 15 mm wide cross section. Each Ti Fix-It plate was loaded in equilibrium in a 4-point bending test (set-up configuration is provided in drawing below), with an applied load of 1000N. The maximum stress in this set-up was less than the yield stress for the…
Q/Answer the following blanks 1. The chemical formula of the maximum copper ore is ...: 2. The chemical formula of the minimum copper ore is .: 3. The copper ore which contain a percentage ratio of iron is .: 4. The pure copper is and ductile and soft with color of .. 5. double fluoride of aluminium and sodium called as 6. the copper-zinc alloys are named as. ***........ 7. The softest and heaviest of all the common metals is. . 8. The zinc ore which is included percentage ratio of Sulphur is 9. Shape, color, and size are properties. 10. The nonferrous metal which is high density and easy workability is ............ 11. In Rockwell test, the major load is applied for a specified time . .beyond zero 12. The of the indent .is a function of the test force divided by the curved surface area 13. The charge is fed through a charging door and is heated to . radiation of heat in open hearth. .mainly by 14. the metals flow and a relatively large permanent set takes place without a noticeable…
QUESTION 3 A Type I offshore life jacket (i.e. personal flotation device) is the type worn by commercial fishermen - it is designed for extended survival in rough, open seawater. Consider such a life jacket that uses an impermeable foam material with a density of 32 kg/m³ - the other parts of the life jacket (straps, fasteners, etc) weigh 0.6 kg and are of negligible volume to the design. a) Draw a free body force diagram for the life jacket. b) Determine the minimum volume of foam material (in L) that is needed for the life jacket in order to provide a minimum 98 N net upward force when it is fully submerged in seawater (as required by US Coast Guard regulations).
In the last few steps, where did 0.4 come from?