Problem 2. Determine the following unknowns on the beam shown below using Area-Moment Method. Consider 150 mm x 150 mm section and E= 80 GPa. Show complete and organized solution. Round-off your answers to two decimal places. a. Vertical Reaction at B in kN. b. Moment Reaction at A in kN-m. c. Deflection at point C in mm. d. Deflection at midspan of AB in mm. b kN/m Minim m c kN B. 3m A=3.2 B=15.5 C=28 10 kN/m

Problem 2. Determine the following unknowns on the beam shown below using Area-Moment Method. Consider 150 mm x 150 mm section and E= 80 GPa. Show complete and organized solution. Round-off your answers to two decimal places. a. Vertical Reaction at B in kN. b. Moment Reaction at A in kN-m. c. Deflection at point C in mm. d. Deflection at midspan of AB in mm. b kN/m Minim m c kN B. 3m A=3.2 B=15.5 C=28 10 kN/m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

SOLVE ONLY ONE OF THE FOLLOWING, using either the Unit Load Method/Method of Virtual Work or the Castigliano's Theorem: A A.) For the truss loaded as shown in Fig A, calculate the total deflection at joint D. Consider uniform cross sectional area A= 500mm² and modulus of elasticity E for all members is 200 GPa. B.) For the rigid frame shown in Fig B, calculate the horizontal deflection at point C. Members have the same moment of inertia of 1440 x 104 cm4 and E is constant at 210 GPa. P= 151 kN P in KN B H O G 4@3m 12 m Fig. A P in kN LL D 4m 120 kN/m B 120 kN/m A 4m Fig. B P in kN 3m 5m
3. Determine the deflection at point C for the beam shown by the virtual work method. 3 kN/m A D C 5 m 10 m 5 m I 21 I E = constant = 250 GPa I = 600(106) mm4
Question 2: Use Castigliano's second theorem to determine the vertical and the horizontal components of the deflection at D of the truss shown in Figure 2. E= 250 GPa, A = 1200 mm² 72 kN T 6 m 10 m B 10 m Figure 2 F 6 m D E 1272
The simply supported beam is made of A-36 steel and is subjected to the loading shown in Figure Calculate the deflection at its center C using the virtual work method. Figure 60 kN 75 kN m A C 4 m 4 m B.
2. By the moment-area method or conjugate-beam method, determine the deflection at the midspan (EIA) for the beam shown in figure below. All figures must be included and drawn straight. (Solve the deflection in terms of El, these two values of E and I are not given in the problem.) P, P2 1.0m B 3.0m 1.0m A 5.0m P2 N 976 676
a) For the fixed steel beam shown in Figure 1, use the double-integration method, i) determine the reactions and moment reactions at the supports A and B, ii) derive the full equation of the deflection curve for the fixed steel beam, iii) determine the maximum deflection đm of the beam AB. EI is constant b) Use superposition method to verify your answer in a) ii) 320 mm k = 290 mm A В L 160mm- Figure 1
Use the moment-area method to determine the lateral deflection at point D for the structure shown in Figure 1. 59 kN 100 kN 1m - 1m B D E = 200 GPa I = 1x10-4 m* 4 m A TTTT t
PLEASE ANSWER ASAP AND REFER TO THE GIVEN VALUES BELOW. Use Slope-Deflection Melhod to solve for the moment at beam BC. Mec in kN-m on the 250 mm x350 mm beam shown in the figure below. Assume E = 80 GPa and use a = 2.0 m, b = 3.4 m. c = 41 kN and d = 46 kN/m
A simply supported beam is subject to a downwards uniform distributed load, w, as shown below. B A uniform distributed load, w L1 L2 The cross-section of the beam is constant with second moment of area I = 3750 mm², and Young's elastic modulus is E = 200 GPa. The distributed load has magnitude w = 220 N/m. If Point B is distance L₁ (Point C), calculate: the downwards vertical deflection at Point B: C C 435 mm from the left end (Point A) and distance L2 = 385 mm from the right end Round your answer to 3 significant figures. X [Units: mm]
Determine the internal moments at the supports of the beam shown using: 1.) ThreeMoment equation 2.) Moment Distribution Method 3.) Slope-Deflection Method Pick two method only Given: E=200GPa I=20x10^6 mm^4 w=8kN/m L1=10m L2=8m
Refer to the figure below: Determine the deflection (delta) in mm at point B. Use E = 200 GPa and I = 2100 mm^4 What is the vertical support reaction at the hinge as shown in the figure below.