PROBLEM 2. A circular shaft AB consists of a 250 mm long, 22 mm diameter steel 125 mm cylinder which is 125 mm long and a 16mm diameter cavity has 125 mm been drilled from the other end B. The shaft is attached to fixed supports at both ends and a 120 N-m torque is applied at its mid- A section. a) Determine the torque exerted on the shaft at A. 120 N.m b) Determine the torque exerted on the shaft at B.

PROBLEM 2. A circular shaft AB consists of a 250 mm long, 22 mm diameter steel 125 mm cylinder which is 125 mm long and a 16mm diameter cavity has 125 mm been drilled from the other end B. The shaft is attached to fixed supports at both ends and a 120 N-m torque is applied at its mid- A section. a) Determine the torque exerted on the shaft at A. 120 N.m b) Determine the torque exerted on the shaft at B.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 40-mm diameter hole is drilled 3-m deep into the steel shaft. When the first torque is removed at point B with 6000-N-m and the second torque is applied at point C with 2000-N-m, determine the following: a) The Maximum Shear Stress in the shaft. b) The angle of rotation of the free end of the shaft. 60 mm 40 mm A В E 2 m 3 m
b) The torques shown in Fig. Q1(b) are exerted on pulleys A, B, C and D. Knowing that each shaft is solid, 120 mm long and made of steel with Modulus of Rigidity of 77 GPa and Modulus of Elasticity of 70 GPa i) Compute the angle of twist between A and C with the aid of free body diagrams. i1) State the direction of the twist (either clockwise or counterclockwise) for question Q1(b)i. 120 N-m 90 N-m D 60 N-m 20 mm C 15 N-m 15 mm 10 mm Fig. Q1(b)
Question (1): A stepped shaft ABCD consisting of solid circular segments is subjected to three torques, as shown in the figure. The torques have magnitudes 12.5 kips. in., 9.8 kips, in., and 9.2 kips. in. The length of each segment is 25 in. and the diameters of the segments are 3.5 in., 2.75 in., and 2.5 in. The material is steel with shear modulus of elasticity G = 11.6 x 103 ksi.(a) Calculate the maximum shear stress Tmax in the shaft. (b) Calculate the angle of twist (pp (in degrees) at end D. 13.5 in. 12.5 k-in. -25 in.- B 9,8 k-in. 12.75 in. -25 in.- 9.2 k-in. 12.5 in. c t -25 in.-
A flanged bolt coupling consists of eight d-mm diameter steel bolts on a bolt circle 267 mm in diameter, and four d-mm diameter steel bolts on a concentric bolt circle 190 mm in diameter. If the torque that can be applied is 8166 Nm without exceeding a shearing stress of 43.32 MPa in the bolts, what is the diameter of the bolts? Round off the final answer to two decimal places.
a: What is the magnitude of torque applied to the shaft? b: The magnitude of the Polar Moment of Inertia of the shaft cross-section? c: The magnitude of the shear stress at r=0in (center of shaft) is?
a) Figure Q5 shows a 1.4 m long steel shaft that consists of a hollow segment AB and a solid segment BC. The shaft is fixed at C and is subjected to two external torques TA and TB at points A and B, respectively. The torque developed at the fixed end C is 750 kN.m in the direction as indicated in the figure. i) Determine the values of TA and TB if the corresponding angle of twist of end A is zero. ii) Calculate the maximum shear stress developed in the shaft. Give your comment whether the shaft will fail or not if the allowable shear stress of the shaft is 75 MPa. 750 kN.m 1.4 m 0.8 m C 160 mm B Тв 200 mm- ΤΑ Section a-a Figure Q5 = [Ans: a) i) T 332 kN.m, TB=1082 kN.m, ii) TCB,max = 60 MPa, TBA,max=45 MPa]
A 0.75" diameter solid steel shaft is connected by the steel bolted coupling shown. The maximum allowable shear stress in the steel is 18 ksi (shaft and bolts). The coupling consists of steel bolts that are 1/8" diameter and the bolt holes are equally spaced and centered on a 4" diameter circle (2" radius from the center of the shaft to the center of a bolt hole). Determine a) The maximum torque that the shaft can carry Ans: /,491"* b) The number of bolts required for the torque in part a). Assume the bolts fail by shearing at the coupling interface and the shear stress is uniform across the bolt's cross sectional area.
I need the answer as soon as possible