Problem 2 - The turbine removes energy from the water in thereservoir such that it has a discharge of 20 ft³/s through the2-ft-diameter pipe. Determine the horsepower delivered tothe turbine. Draw the energy and hydraulic grade lines forthe pipe using a datum at point C. Neglect friction losses.15,n

Given:Discharge, Q=20 ft3/sDiameter of pipe, d=2 ft

Answered: Problem 2 - The turbine removes energy…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Use f=0.012 for all pipes and initially assume equal flow in pipes AB and AE. Determine the corrected flow in pipes BC, BE, AB, DE, and AE of the pipe network shown. 0.6 m/s A 300m B 300m 0.4 m/s 300mm 250mm 424m 300m 300m 250mm E 300mm 250mm 300m D 0.2 m/s 250mm
The 600 mm diameter pipe conducts water from reservoir A (El. 61 meters) to a pressure turbine (El. 4.60 meters), which discharges through another 600-mm diameter pipe into tailrace B (El. 0 meter). The loss of head from A to the entrance of the turbine (pt.1 ) is 5 times the velocity head in the pipe and the loss of head from the exit of the turbine (pt.2) is 0.20 times the velocity head in the pipe. If the discharge is 708 Liters/second, Determine the efficiency of the turbine if the output power is 480 hp. a. 61.20% b. 69.15% c. 75.72% d. 86.88% e. 89.57%
A Borda's mouthpiece 200mm in diameter discharges water a head of 4m. Determine the discharge in liters/sec and the diameter of the jet at the vena contracta. Cv= 0.98, Cc=0.62
Water is being pumped from Lake 1 to Lake 2 by a 15.4 horsepower pump with an efficiency of 65%. If the head. loss in the system is 15.0 ft, determine the flowrate into Lake 2 (ft3/s) Lake 1 1x 8-in. inside- diameter pipe Pump 30.0 ft Lake 2 38.5 ft
Water flowing through a contraction pipe with diameter of 20mm and 5 mmrespectively. If the velocity of water at the larger diameter is 0.5 m/s, determine the discharge in the pipe and the velocity at the smaller diameter. Based on your result,state the correlation between flowrate and area of pipe diameter.
Which of the following equations below describes the system head of the piping shown below. The total length of the pipe is 154 ft. Take the friction factor to be 0.026. The pipe used has a nominal diameter of 4 inches and Schedule No. 40. The system head H is in ft and the flow rate Q is in ft^3/s. Hint: You need to use the Tioga table and K value for minor losses. Z₂ = 107 ft Reservoir B 90° regular screwed elbow Pump Z₁ = 53 ft Reservoir A A) H=51+25.98(Q^2) B) H=54+24.98(Q^2) ⒸH=54+25.98(Q^2) ⠀
Determine the number of prismatic joints This is the exchange of the fixedness of an element Location of pairs Inversion of pairs Reformation of pairs Conversion of pairs 28°C Partly sunny
2. draw fbd
Q.9) If the faucet (gate valve), at E is fully opened and the pump produces a pressure of 350 kPa at A, determine the flowrate out from the faucet at E. The valve at B remain closed. The pipe has an inner diameter of 30 mm, and f=0.01. Include the minor losses of the tee (K=0.4), the two elbows (K=0.9), and the gate valve (K=0.19). 0.65 m 3 m B 5 m
5. Determine the total discharge in the pipes. N = 0.013 El-50 El.0 Li = 8050 m d;= 200mm dz= 200 mm L2= 500 m
For the frictionless syphon shown, determine the discharge and the pressure heads at A and B. Consider a pipe diameter of 210 mm with the nozzle at the exit having 140 mm diameter. Consider a datum plane that is 0.16 meters above point A. 2.44 m 1.22 m 0.15 m
(12 mins) The penstock supplies water from a reservoir to the Pelton wheel with a gross head of 516 m. One third of the gross head is lost in friction in the penstock. The rate of flow of water through the nozzle fitted at the end of the penstock is 1.8 m³/s. The angle of deflection of the jet is 165º. Determine the power (MW) given by the water to the runner. Take speed ratio = 0.45 and C₁ = 1.0. Use p = 998 kg/m³. Round off your final answer to two decimal places.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS