answer with steps Problem 2For the given frame shown, it is subjected to a concentrated load of 100 kN at the midspan of BC. Using moment distributionmethod (four iteration) and with El constant in all beams and columns, determine the following:100KNCAD3 m3 m4 m5 m Question 4Moment at support A in kN.m.Ans.: Blank 1 kN.mBlank 1 Add your answerQuestion 5Moment at support D in kN.m.Ans.: Blank 1 kN.mBlank 1 Add your answerQuestion 6Moment at support E in kN.m.Ans.: Blank 1 kN.mBlank 1 Add your answer

Fixed end Moment (Mf) MfAB = MfBA = 0 MfBC = -(PL/8) = - (100×6/8) = - 75KNm MfCB = +(PL/8)=…

Problem 2 For the given frame shown, it is subjected to a concentrated load of 100 kN at the midspan of BC. Using moment distribution method (four iteration) and with El constant in all beams and columns, determine the following: 100KN ... C A D 3 m 3 m 4 m 5 m

Problem 2 For the given frame shown, it is subjected to a concentrated load of 100 kN at the midspan of BC. Using moment distribution method (four iteration) and with El constant in all beams and columns, determine the following: 100KN ... C A D 3 m 3 m 4 m 5 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 8 The gate AB is 4.60 m long and 2.4 m wide perpendicular to the paper and is hinged at A with a…

A: To determine the weight of the concrete block.

Q: Resolve F, into components along the u and v axes and determine the magnitudes of these components.…

A: Given data, F1 = 250 N F2 = 150 N Resolve the F1 and determine the component of these force.

Q: 60cm Waw A 23cm 6- 16cm SG=08 20cm 20cm SG= 13.6 SG=136 Given heights: 60cm, 23cm, 16cm, h, 20cm, 20…

Q: The rod has a weight of 7.8 lb/ft. It is supported by a ball-and-socket joint at C and a journal…

A: Given data:- The given rod weight is, 7.8 lb/ft

Q: Find the Displacement of object if work done on object is 500 J and force applied on object is 22.25…

A: Given data : Work done is denoted by W Force applied on object is denoted by F Required :…

Q: Discuss practical applications on how does water in the slope induces instability in constructions.

A: Water is goes inside the soil through pores of the soil and take place in soil void by replacing the…

Q: What is the difference between velocity pressure and velocity head?

A: Answer difference between velocity pressure and velocity head is following

Q: 4. The compound beam is subjected to a uniform dead load of 2 kN/m and a single live load of 14 kN.…

Q: / Find the area of the region that lies inside r =6 sin0 and outside r=2+2sin0

Q: COPY THE GIVEN TRUSS AND SOLVE FOR THE MEMBER FORCES AB, AC, BC, BD, BE, BF, CF. DE, EF

Q: multiply the numbers. 73* 3

Q: Draw the shear and moment diagrams of the following beams by semi-graphical method. Write the shear…

A: Given: Required Shear force and bending moment diagram

Q: Force-couple systems: A couple is a pair of forces, equal in magnitude, oppositely directed (sum of…

Q: The cantilever beam geometry shown is made from steel E=200GPA. Determine the deflection and the…

A: To calculate the value of slope and deflection at point B, using the double integration method. In…

Q: Determine the Radius of Gyration about the X axis

A: Consider the free body diagram;

Q: Derive expression for mode shapes and frequencies of a uniform cantilever beam and determine the…

A: Mode shapes: The special initial displacements of a system that cause it to vibrate harmonically…

Q: Help!!!! Answer all correctly

A: Step 1:PART A:Step 2:PART B:Step 3:PART C: Step 4:PART D:

Q: SHOW COMPLETE ILLUSTRATION & SOLUTION A line 50m long was paced by a civil engineer three times and…

A: Given data in question 50 m long line Paced distances 3 times Paced distance of another line 3…

Q: Q4. Determine the unknown force R in each of the following diagrams. a. b. 198 N 38.6 110 R 210 N 75…

A: To find value of R

Q: Make an introduction about Fluid Displacement Method for Measuring Volume Solids. Cite your…

A: To find the volume of an object or solid we can use the fluid displacement method.

Q: Problem 10.6 - Locate the centroid of the section and determine the moment of inertia of the beam…

Q: Hi! Help me with this please. Thank you so much! In the equation D = Ks + C, C represents the.

Q: Explain force of friction between two bodies. If a wooden block of weight 100 N rests on a…

A: Given data- A wooden block system as shown- Weight of block (W) = 100 N coefficient of friction μ =…

Q: The cantilever beam geometry shown is made from steel E=200GP.. Determine the deflection and the…

A: Due to loading on the beam acting at any point or entire beam makes the beam deflect and that…

Q: 5. Cross ties are used if the distance between a bar and the corner bar is greater than ... а. 100…

A: Cross ties are used when the distance between a bar and corner bar is greater than 150 mm. Cross…

Q: Please

A: As there are multiple questions posted, according to the guidelines, only the first three are being…

Q: case #2, from what point is the 2.5 in the equation? is it from the fixed to the point P? or Point P…

Q: The two forces are equivalent to a force R that has a line of action pass through point A. Determine…

Q: Determine the x- and y-coordinates of the centroid of the shaded area. Y I Ti 0.34 al TE Answer: (x,…

Q: Explain about the flat-blade dilatometer.

A: The Flat-blade Dilatometer test (DMT) is an in-situ testing method to determine the strength and…

Q: Determine the force (P) required to cause impending motion, given that us = 0.43 and µk = 0.25. F1 =…

A: solution - Given Data:- F1 = 506 Coefficient of static Friction = 0.43 Find, the value of P

Q: The 90 Ib force of Figure is the resultant of three coplanar forces and a couple Determine the force…

A: Given 90 lb force is the resultant of three coplanar forces and a couple. Required The unknown…

Q: Two forces are applied to a hook. Variable F₁ F2 a b C d Value 50 lb 30 lb 2.5 ft 3.5 ft 5.5 ft 2.5…

A: Given:Required:Force In Cartesian vectorResultant force vectorMagnitude of resultant forceCordinate…

Q: Why are the arrows in the right direction when they are in the left direction in the original image?…

A: Required: Explanation for Why forces direction have been considered opposite to that shown in…

Q: Question 3 Find the ratio Q1 Q₂ 30⁰ Q₁ Q₂|

A: Given- Angle of bend=30o, It is needed to find the ratio of discharge going up (1) & going down…

Q: 15 10 2 5 •10 y = C 10 T 15 8 20 The cross-section of a hollow box beam is shown. Grid units are…

Q: Critically discuss the relationship between level measurement and pressure measurement.

A: Pressure measurement : 1. Pressure and DP transmitters measure levels based on the principle that…

Q: There are two questions to answer. The first question is a truss problem and the second is a frame…

A: Question 1. TrussCut at Section a-a. Assume all forces are in tension. Question 2. Framea. Draw the…

Q: Compute for m if fc'=32MPa and fy=400MPa. Use 3 decimal places

Concept explainers

Stair construction and layout

Stair is a type of vertical transportation in a building which consist of a series of steps in a flight of stairs that enable the vertical movement of people and materials from one floor to another. A staircase consists of steps that comprises of riser & tread, handrail, baluster, stair stringers, newel post and waist slab. The construction of staircase with all the components is termed as stair construction. A staircase is an enclosure that contains the entire stairway. The materials used for the construction of stairs are bricks, reinforced cement concrete, stone, lumber, steel and a combination of these materials.

Question

answer with steps

Problem 2
For the given frame shown, it is subjected to a concentrated load of 100 kN at the midspan of BC. Using moment distribution
method (four iteration) and with El constant in all beams and columns, determine the following:
100KN
C
A
D
3 m
3 m
4 m
5 m

Question 4
Moment at support A in kN.m.
Ans.: Blank 1 kN.m
Blank 1 Add your answer
Question 5
Moment at support D in kN.m.
Ans.: Blank 1 kN.m
Blank 1 Add your answer
Question 6
Moment at support E in kN.m.
Ans.: Blank 1 kN.m
Blank 1 Add your answer

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Please illustrate and solve the problem. thankyou
Give the procedures in finding the friction factor fusing the Moody Chart. Provide illustrations.
Give me right solution with clear calculations
5.0 m (100+SN) KN> 144 KN 5.50 m E 6.0 m C 7.0m K 5.0 m O 120 KN 96 KN M U W Note: SN is the sum of your Student Number, e.g. 201802475=2+0+1+8+0+2+4+7+5 = 29 Instruction: Solve the following problem completely using portal method and write the solutions neatly in the plate template. Summarize your final answers at the end of each problem. Round off your answers to 3 decimal places. 1. Portal Method: The frame shown is subjected to lateral loads as shown. Supports S, T, U V, W and X are rigid supports. Determine the following: a) The shear forces in columns and girders. b) The axial forces in columns and girders. c) The moment at the end of each member. d) Summarize your results by drawing the frame with the internal forces. 4.0 m R 4.20 m 4.50 m 5.0 m
In (Figure 1), F = {80i + 96j + 48k} lb. Figure 1 ft -2 ft 3 ft 45° B 1 of 1 Part A Determine the magnitude of the moment of F about point A. Express your answer in pound-feet to three significant figures. 15] ΑΣΦ11 MA = Submit Part B α, B, y = Submit Request Answer Provide Feedback Determine the coordinate direction angles of the moment of F about point A. Express your answers in degrees to three significant figures separated by commas. vec U/ ΨΕ ΑΣΦ ↓↑ vec Request Answer ? lb. ft ? Next >
Q1. a) Figure below is an object. You should sketch the top view, side view and front view of first angle orthographic projection. b) Sketch the isometric view of the object. Point A should be the lowest point of the object. 100 36 36 28. 2 HOLES, DIA 12 A 12 45 75 12 12 56 A 63 15 25
Solve for dimensions Flow rate •Mass
A.Compare and contrast the Ritcher scale and the moment magnitude scale in own words.
Final Answer should be in 2 decimal only.
(b) Express the force F as a Cartesian Vector. Assume that the magnitude of F is |F| = 771 N.Please see the figure attached.
final answer must be in two decimal only.