Answered: Problem [2] Find the equivalent…

Engineering

Electrical Engineering

Problem [2] Find the equivalent inductance of the circuit. Assume all inductors are 10 mH. ll ll ll

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter20: Capacitance In Ac Circuits

Section: Chapter Questions

Problem 5PP: Three capacitors having capacitance values of 20F,40F, and 50F are connected in parallel to a 60 -...

See similar textbooks

Related questions

Q: As discussed in your reading material, the MAIN reason for calculating a capacitance value is to…

A: (i) The main reason for calculating capacitance value is to improve power factor (ii) Most…

Q: What will happen to the value of the current if the capacitance will be increased or decreased?…

A: The solution is given below

Q: Find the equivalent inductance between terminals A and B in the following figure. Assume no mutual…

A: If three inductors of inductance L are connected in parallel then equivalent inductance is L/3. If…

Q: Determine the total capacitance, total charge, individual voltage drop and charges across each…

A: given circuit We have to calculate total capacitance, total charge, individual voltage drop an d…

Q: A voltage of 47V RMS is applied across a real inductor. The current through the inductor is measured…

A: As inductor possess its own resistance the phase angle between its current and voltage is a little…

Q: a. Show how you would connect all five capacitors to get a maximum capacitance and find the maximum…

Q: Find the equivalent inductance of the circuit shown in the image below. Assume all inductors are 80…

A: We need to find out the equivalent inductance for given circuit.

Q: What is the maximum inductance that can be obtained by connecting four 2-H inductors in series…

Q: Three capacitances of 4 µF, 6 µF and 5 µF are connected in series across a 110-volt dc source. Find…

Q: The diagram shows an inductor that is part of a circuit. The direction of the emf induced in the…

Q: 4. The current through a 10-mH inductor is 10-2A. Find the voltage and the power at t= 3s.…

A: we need to determine voltage and power at t = 3sec.

Concept explainers

Capacitor

The capacitor is an element used to store electrical energy in the electrical field. A capacitor is a form of passive energy.

Question

Problem [2]
Find the equivalent inductance of the circuit. Assume all inductors are 10 mH.
ll
all

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Three capacitors having capacitance values of 20F,40F, and 50F are connected in parallel to a 60 - Hz power line. An ammeter indicates a circuit current of 8.6 amperes. How much current is flowing through the 40F capacitor?
A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating of 600 WVDC. The capacitor and resistor are connected to a 480-V, 60-Hz circuit. Is the voltage rating of the capacitor sufficient for this connection?
A capacitor uses air as a dielectric and has a capacitance of 3 F. A dielectric material is inserted between the plates without changing the spacing, and the capacitance becomes 15 F. What is the dielectric constant of this material?
You find that a 25-F capacitor connected to 480 VAC is defective. The storeroom has no capacitors with a 480-VAC rating. However, you find two capacitors rated at 50 F and 370 VAC. Can these two capacitors be connected in such a manner that they can replace the defective capacitor? If yes, explain how they are connected and why the capacitors will not be damaged by the lower voltage rating. If no, explain why they cannot be used without damaging the capacitor.
A postage stamp mica capacitor has the following color marks starting at the upper left dot: yellow, violet, brown, green, no color, and blue. What are the capacitance value, tolerance, and voltage rating of this capacitor?
You are an electrician working in an industrial plant. You discover that the problem with a certain machine is a defective capacitor. The capacitor is connected to a 240-volt AC circuit. The information on the capacitor reveals that it has a capacitance value of 10 mF and a voltage rating of 240 VAC. The only 10-mF AC capacitor in the storeroom is marked with a voltage rating of 350 WVDC. Can this capacitor be used to replace the defective capacitor? Explain your answer.
You are working in an industrial plant. You have been instructed to double the capacitance connected to a machine. The markings on the capacitor, however, are not visible. The capacitor is connected to 560 volts and an ammeter indicates a current of 6 amperes flowing to the capacitor. What size capacitor should be connected in parallel with the existing capacitor? What is the minimum AC voltage rating of the new capacitor? What is the minimum DC voltage rating of the new capacitor? What is the minimum KVAR size that can be used in this installation?
In reference to the load, how are capacitors connected to help prevent voltage spikes and surges? Are capacitors connected in parallel or in series with the load?
List the five capacitor replacement rules.
Find the equivalent inductance of the circuit. Assume all inductors are 10 mH.
Find the equivalent inductance as seen from the terminals shown in the figure.
You are modifying the design of an existing inductor and want the inductance to be 1/2 of it's current value. You could achieve this by which of the following options. Select all that apply. Question 1 options: Decreasing the number of windings by a factor of 2. Decreasing the length of the inductor by a factor of 2. Increasing the area of the inductor by a factor of 2. Increasing the number of windings by a factor of 2. None of the other responses are correct.