Problem 2 Determine the total time t (in hrs.) required to fil the spherical tank with liquid whose specific gravity is 2.50. The mass flow rate of the liquid is 400 kg / min. and the diameter of the tank is 4m. Pump Spherical Tank

Q: 1. Outcome #3. You must show and explain all work. A speed boat utilizes a jet pump for propulsion.…

A: Given: Thrust force (F) = 130 kN = 130,000 N Inlet area at station 1 (A1) = 0.07 m² Velocity at…

Q: Which of the following statement is incorrect? Select one: O Friction is high for dry surface O…

A:

Q: Describe Pascal’s law?

A: Pascal’s law states that the static pressure acted on a liquid particle at rest is normally towards…

Q: isc SC

A: given:discuss how the cylindercal square is used?

Q: why is there no translational component for the kinetic energy of this problem? thank you!

A: here question asked that why translational component of kinetic energy is not considered?

Q: The diameter of the cylinder in a scrap baling press is 150 mm. The stroke of the cylinder is 2.5…

A: This problem is related to fluid mechanics. Fluid mechanics is the subject of mechanical engineering…

Q: solutions are given, please resolve to get these solutions

A:

Q: 11. Bicycle tires for street racing are very narrow. Why aren't they made wider if the bicycle needs…

A: The tires of the bicycle is made narrow to reduce the wind resistance, rolling resistance, and…

Q: Define the Nonmechanical Forms of Work.

A: In thermodynamics, the non-mechanical work is the work which is determined by the non-contact or the…

Q: Problem 6: The top wall moves with velocity Vtop = 1" and the bottom wall is m S stationary. Inside…

A: VISCOSITY is defined as internal resistance offered by one layer of the fluid to the adjacent layer…

Q: Because of the additional equipment installed, it requires an additional flowrate of 800 CFM. The…

A:

Q: 9. In a factory, packages are moved from a room on the second floor to a station on the first floor…

A: COEFFICIENT OF FRICTION DEPENDS ON MATERIAL

Q: Please help. Written on paper not typed on computer or keyboard please. Need help on all questions.…

A:

Q: DEFINE THE MECHANICAL FORMS OF WORK ?

A: When work is produced by the application of force, then the work is called mechanical work. The…

Q: ood day. I am trying to review for examinations and require assistance for these questions... Horse…

A: Given

Q: In a machine, the maximum torque transmitted by a shaft exceed by 15 % the actual torque. A power of…

A:

Q: In a hydraulic press machine the diameters of the effort and load pistons are respectively 25 cm and…

A:

Q: solve parts 4 and 5 please

A: To draw Mohr circle and to show the orientation of the element of maximum in plane shear stress

Q: Dimension this object.

A: Find Provide the dimension of the given project.

Q: 6 m

A:

Q: 2. For diagram will be accepteu) do the following: a) Determine the angle a (alpha). b) Determine…

A: Given question is related to solid mechanics. Given data: F1 = 600 N, F2 = 400 N. We have to use the…

Q: Please help. Written on paper not typed on computer or keyboard please. Need help on all questions.…

A:

Q: Joe takes his little brother Andy down the the playground for an afternoon out. Andy would like to…

A: Considering a frictionless seesaw mechanical system. Mechanical Advantage of the system is the ratio…

Q: Start a new Part in SolidWorks. Make a 1" diameter x 5" tall cylinder. Put a 0.5" diameter hole…

A: Given that-Diameter of cylinder = 1'' = 1 inchHeight of cylinder = 5'' = 5 inchDiameter of hole at…

Q: The M777 lightweight 155 mm howitzer is a piece of artillery whose rounds are ejected from the gun…

A:

Q: What is its minimum width if it produces 1000 minima?

A: The expression for the dept of the slits is given by the expression, Dsinθ=mλ For the minimum width…

Q: JC BRA JC Ma = 2.5kg BRD BAD Mb=7kg Given that: The line of force for BRD is 5cm. Distance JC to Ma…

A: Mass, Ma= 2.5 kg Distance between JC and Ma, a= 16 cm Mass,Mb= 7 kg Distance between JC and Mb, b=…

Q: 1. average velocity is correct (-0.75 m/s) but instantaneous velocity (-1 m/s) is incorrect can you…

A: Given :    To find : instantaneous velocity v when t =4 s

Q: (1) A rod of length L has a small square cross section b²; the density of the material is p. Just by…

A:

Q: The elastic modulus of a material... A....determines when a material can be permanently deformed.…

A:

Q: b) The bore diameter of each cylinder in a six-cylinder four-stroke internal combustion engine is 32…

A: Find  Mean effective pressure Indicated Power

Q: c) The bore of each cylinder in a six-cylinder car engine is 52 mm and the stroke for each piston is…

A:

Q: (1)Changethedistributedload from 400 lb/ft to 550 lb/ft.Keep inmind that this change will result in…

A:

Q: It is required to design a tennis ball for recreational use by settlers on Mars. The primary…

A: Given data:LE - Drop height on Earth (m) = 2.54 m gE - Gravitational acceleration on Earth (m/s2) =…

Q: 25) A metal sphere is dropped into a deep tank containing a viscous liquid. It experiences a…

A: When a metal sphere is dropped in viscous liquid, initially, net force acting on it is its weight…

Q: Please help. Written on paper not typed on computer or keyboard please. Need help on all questions.…

A: Step 1:a. Equation for the differential area aligned horizontally The differential area element dA…

Project Management Techniques

The guideways or the roadways that are undertaken to perform a project efficiently and all the tools required to accomplish the task are the general outlines for project management techniques.